Need some help ...
 
Notifications
Clear all

Need some help ...

17 Posts
5 Users
0 Reactions
3,621 Views
RGB_Mixer
Posts: 270
Topic starter
(@rgb-mixer)
Reputable Member
Joined: 12 years ago
[#54595]

QUESTION: What do I need to build a good Falcon Player for use on NON Falcon controllers? Falcon Player on a PI. Or Beagle Bone?

I have a situation and need some information. We have several Falcon F16v3 controllers running two displays and do well.

I have not been able to setup the Falcon F16 to handle 1020 leds per output. I need 6 channels for the new Leaping Arches display.

Either Falcon does it or I need to use Advatek which I know handles 1020 per channel.

Falcon Player can drive the Advatek DX controller as these arches cover 300+ feet.

Wireless IS an option but with limited supplies - Advatek offers a wireless solution (not cheap). Sorting this out is paramount. Logistics work on the physical layout. I have considered some smaller controllers with a channel count of 1020+ and WiFi routers/access points.

Apparently the "CHIP SHORTAGE" has affected allot more than the auto makers.


16 Replies
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

I had similar issue but couldn't find a board to handle 1000 pixels, so I split them into 2-500 pixel runs. It worked seamlessly.


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

For the 300 feet, look at a Differential Expansion Board for your F16. Here is a link. If you have F16-V4 there is the same except for V4.
https://www.pixelcontroller.com/store/expansion-boards-and-receivers/56-4-string-differential-receiver-board.html


Reply
RGB_Mixer
Posts: 270
Topic starter
(@rgb-mixer)
Reputable Member
Joined: 12 years ago

Yup - I have the logistics worked out. I was using RS-485 for GECE pixels and ws2811 on a E684 before it became available as a mainstream "OPTION".

Unfortunately there are no NEW boards available. Advatek increased prices with this "CHIP SHORTAGE".

I looked @ one F16 as master and two F16 4 channel as remotes using their built-in WiFi. A pretty easy solution, if it works as expected. The claim of 1024 pixels per channel on the V3's? Apparently not so - and that seriously annoys me.

HARDWIRED: I would run about 100' ethernet in 2 directions, best layout.

I can use Advatek (1020 max output) and a few WiFi routers in MESH mode to achieve a single network if I have the time to re-engineer a bit.

I am researching Falcon Player on a PI to run the shows. I use a dedicated PC here @ home for my shows.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I assume that since you are trying to put more than 680 pixels on a WS2811 string you are using the slower 50ms refresh rate. Based on the spec sheet for the F16V3 it handles 1024 (aka 1K) pixels per port when no expansion port is behind the port in question.


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

A WiFi option to consider is FPP Master/Remote (now player remote) Load sequence on both player and remote....you don't sync e1.31, FPP sync's to each other, therefore plays same sequence in many location with minimal WiFi traffic. Then maybe look at DKulp's K4-PB.

https://www.wiredwatts.com/klk4pb

K4 PB

Reply
rayhjr
Posts: 972
(@rayhjr)
Noble Member
Joined: 12 years ago

Have you thought about Scott's Boards?
https://github.com/computergeek1507/PB_16
He claimes "700 pixel per output at 40 FPS or 1300 at 20 FPS".
I use a 4 port remote to run my Mega tree with 592 pixels on 3 ports and 260 star on the last.
I have never tried or tested 1300 so I have no Idea if his claim is true.
Some Boards are compatible with the Falcons, not sure of which ones, because I don't have any Falcon Controllers.


Reply
RGB_Mixer
Posts: 270
Topic starter
(@rgb-mixer)
Reputable Member
Joined: 12 years ago

This entire display is for "Celebration Of Lights" in Oshkosh, WI (FB page too) - a community sponsored event. This is the NEW addition to the family and it is going to mark the 20th year. It is a big thing (and so is this display). 300+ feet of Leaping Arches to commemorate the 20th Anniversary.

Quite frankly, I am swamped and really do not have the time to research every possibility and test them. I want to use what I know works and I will entertain viable options.

I am trying to use what I have available. I have one F16v3 and a DX board with modules. If I cannot do this as planned, I will use Plan "B". The logistics must be kept simple. More than ONE cable for 10 arches is not acceptable. I have to hard line this because it is designed around the 1024 pixel limitation (only need 1020). This is a public area so cable count MUST be kept at a minimum for the safety of the public and the display itself.

Plan "A": I want to try and use the F16 we have and one expansion board for DX'ing the other 4 channels on two receiver modules. Two full 1020 pixel channels off the F16 and two off of each remote. It should be possible using the data only line. Or at least I would HOPE SO. Then it eliminates the need for a Falcon Player PI.

Plan "B": the Advatek DX. It requires Falcon Player to play the sequences. Advatek has a WIRELESS controller - NOT CHEAP!! I can tolerate two Ethernet cables this year.

No audio, just effects. I do not have time to research all the WiFi scenarios. That is on next year's "TO DO" list.

If you want to see the progress ... my FB Page: "Our House 1374" I will update this page as the assembly progresses. I am in a holding pattern until we get the center supports welded, LEDs (From Ray Wu's) and weld up the steel bases. 2 weeks out on some materials as of today.


Reply
RGB_Mixer
Posts: 270
Topic starter
(@rgb-mixer)
Reputable Member
Joined: 12 years ago

What I need is a sACN generator. Putting a PC out in the field is NOT a good idea - long story. I believe the Falcon Player does send sACN data over Ethernet - I have asked the question on the Falcon Player board but have not had a response from the Falcon Player folks yet.


Reply
RGB_Mixer
Posts: 270
Topic starter
(@rgb-mixer)
Reputable Member
Joined: 12 years ago

I am all for the WiFi connection. I would do that if I could find TWO F4v3 Falcon controllers - that is pretty much the problem using Falcon. Other is the Pixel count which needs to be 1020 per channel for 5 arches each. Six channels have to run this display. So it is a brain buster to sort out the options and find one that works.

Thanks :mellow:


Reply
Page 1 / 2
Share: