FPP install help re...
 
Notifications
Clear all

FPP install help required

52 Posts
8 Users
0 Reactions
16.5 K Views
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

Mikekrebs,

I understand. However, the reason for this is that this is for a tune to matrix which is on a separate building (garage) from the rest of the show. It is supposed to run independently of the everything else due to it's position in the yard.
I could make it very easy on myself and just run a ethernet cable to that building and run the matix and show off the same laptop that ii currently use for the show, but:
a) I live in a very cold area, and, as the wire would have to cross the driveway, it would have to be strung up 8' or so in the air and the wind would blow it around, possibly breaking the cold wires. I thought this thing was supposed to be a stand alone computer that would take care of the matrix by itself.

Ray


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

I also thought that doing the matrix with the Pi would cut down on digital traffic over the network for the regular show


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

the lights work, but I still do not have wifi to the Pi


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

it's like when I plug the eth0 cable, the wifi turns off


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

I do not have a keyboard plugged into it, but I do have a monitor attached to it.

Yes I have the correct SSID and password, because it will work if the controller is not plugged into the Pi.

E682 IP 192.168.2.2 (now) subnet 255.255.255.0
Not sure how to check or see the network on the pi
The show laptop is wired through a switch to the rest of the show. I am trying to make the Pi work with a different laptop, wired to a home router.
laptop to router - router to Pi OR Pi to E682.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
bcer960 wrote:I do not have a keyboard plugged into it, but I do have a monitor attached to it.

Yes I have the correct SSID and password, because it will work if the controller is not plugged into the Pi.

E682 IP 192.168.2.2 (now) subnet 255.255.255.0
Not sure how to check or see the network on the pi
The show laptop is wired through a switch to the rest of the show. I am trying to make the Pi work with a different laptop, wired to a home router.
laptop to router - router to Pi OR Pi to E682.

@ 29:38 of this video shows the correct method of cabling for your setup


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago

Thank-you Angus40. I believe I have it set up this way, except that when I have the controller connected, I cannot access the Pi with wifi. I do not understand why. Is there some setting that disconnects the wifi when an eth0 cable is connected?


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
bcer960 wrote:it's like when I plug the eth0 cable, the wifi turns off

when both interfaces are in the same subnet, the wifi interface gets turned off. only one interface per subnet is allowed.


Reply
Posts: 247
Topic starter
(@bcer960)
Reputable Member
Joined: 10 years ago
MartinMueller2003 wrote:when both interfaces are in the same subnet, the wifi interface gets turned off. only one interface per subnet is allowed.

so, I have set the Pi eth0 to 192.168.2.1 and the controller to 192.168.2.2
the Pi wifi is 192.168.1.101
I still can't get wifi if the Pi is connected to the controller.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

It sure looks like something odd is afoot. I am going to suggest a test configuration (you may have done tis before but now that things are on separate subnets we get some useful info).

  • Disconnect everything from the PI Eth0 interface.
  • PI connected through WiFi to a computer on the 192.168.1.x subnet and has its browser monitoring the PI using its WiFi address
  • You indicated this works.

Connect a separate computer to the PI Eth0 interface (with a manual IP in the 192.168.2.x range) and try to access the FPP web page using a browser.

  • Does the computer talking via the WiFi interface still have control of the UI?
  • Does the Eth0 connected computer have control of the UI?

Reply
Page 4 / 6
Share: