I finally got a chance to wire up lights to a project I am working on. It is a stand alone wreath for my mother. I am having some sort of an issue when playing sequences and in the software test area. There is some sort of flickering and nothing is running smoothly. I'm sure if I have everything setup and configured correctly but can't figure this out. I will tell you what I have done and see if anyone has some suggestions.
-First, I am using a Raspberry Pi B+ loaded with FPP version v1.8-4-g0b4865c
-Lights, SH-1903/2811 square shape Pixel nodes that are supposed to have 2811 chip, using a total of 54 nodes
-Software used was Vixen3 with sequences exported to .fseq output
-Using a 12v power supply to provide power to the pixels and a seperate 5v power supply to power the Pi
-wiring, 12v positive to 12v on the pixels, ground is tied to ground on pixels and Pin 25 on the Pi
-Di of the pixels is tied to Pin12/GPIO18 of the Pi
- FPP is Output configured with the "Other" tab, RPIWS281X checked, Start Ch. 1, Ch Cnt. 162
String #1 Pixels 54 (GPIO 18), Color Order RGB
Below is links to videos showing what I am seeing:
I have tried more than one string of pixels and a pixel strip, still see the same issue. I have tried a different Pi
with no change. Reinstalled the FPP software. Confirmed that all GPIO are unchecked except for RPIWS281X.
Rebooted and confirmed that the sound has been turned off. Changed the power supply on the Pi with a little
improvement but no solution. Have I missed anything? Any suggestions?
Your help is appreciated.
I was not aware a Pi could directly drive 2811 pixels. Pi is 3v logic - 2811 expects 5 v signals.
Also make sure that the pi isn't supposed to drive 2801 pixels instead of 2811 - the 2801 has a clock signal.
The way I boost up to 5v levels is with a 74hct04 hex invertor. Power it with 5v. Take two in errors back to back so you get the same signal out you put in but at 5v logic instead of 3v. Cheap and easy to find in dip package.
Not a bad idea, the Pi has 5v output pins on it. I could power the chip with the Pi. Feed the output to the input of the first invertor, take the output of the first and feed it to the input of the second, and then take the output from the second and feed to the Di of the pixels. Will give it a try.
Yes the PI is a 3v output device so you will need a level shifter and you should have a 300 ohm resistor in series with the pixels. RonP has a PI to pixel adapter board that has the level shifter built in. It also has a lot of other stuff that you can leave unpopulated.
Be certain to a) use an HCT part. Others won't work. B) have a 1uf decoupling cap right at the part. HCT parts are fast and useful, but ring like bells at every transition of you don't have the cap connected.
Can you point me to his site. I might me interested in one.
Shockwave wrote:Be certain to a) use an HCT part. Others won't work. B) have a 1uf decoupling cap right at the part. HCT parts are fast and useful, but ring like bells at every transition of you don't have the cap connected.
Sorry, you lost me with the cap and where it goes. The part I'm looking at is NTE74HCT04 from Fry's. I have one not far from me. Where should the cap go?
I'm having the same discussion on the FPP forum, you can see the other responses here http://falconchristmas.com/forum/index.php/topic,4739.new.html#new
The capacitor goes between 5v and ground as close to the chip as possible
mikeh65 wrote:Can you point me to his site. I might me interested in one.
http://www.ronsholidaylights.com/
