Hi guys, I'm just begining to dip a toe in the rgb pixel pool. I've ordered some strings (WS2811), a power supply (5v60w) and a few DMX512 module & decoders. I have spent quite a bit of time on the wiki page and reading through the dmx forum but I just can't seem to get an understanding of how to set this up! I know the problem must be me because their's tons of info. Here's what I need help with:
1. A generic step by step process from computer to lights. I get confused... if I have a converter does that go into my ren64 then to a rgb controller in the yard like an ssr? I just can't seem to get an understanding and I'm frustrated!
Thank you for your understanding and input.
The path is as follows:
Computer -> DMX Dongle (USB) -> Converter -> LED String
Perhaps a few screen shots and/or links to the devices you are using might help us help you - it's not 100% clear what you have...
budude wrote:Perhaps a few screen shots and/or links to the devices you are using might help us help you - it's not 100% clear what you have...
Sorry I haven't got back sooner, I've been out for a few days. Anyway, I currently have 2 Ren64XC's, 16 SSRez's and 16 SSRNeon LED's. I just received two more Ren64XC's from wjohn and have ordered 40 more SSRNeon LED's from a current group buy. I ordered (from DIYLEDExpress) a few WS2811 pixel strings, a 5v 60w power supply and a few DMX 512 Module & decoder;DC5V input. I'm using Vixen 3.0.4
I was thinking of adding some rgb flex strips this year as well.
So I go from my computer to an E682 then what? I understand I can add the power straight to the board if I go with a E681 or 682, but I get lost on how they all connect. I understand this is probably a loaded question because I'm sure there are many options. So far from what I have read I like the e681 or 682. Do I run the dmx signal over a cat5 line or do i need a dmx cable?
this may help > page 71 Acl 101 guide .
you can get it here >
http://auschristmaslighting.com
Pic removed
My appologies to FastEddy For not Requesting permission to upload this pic.
angus40 wrote:this may help > page 71 Acl 101 guide .you can get it here >
http://auschristmaslighting.com
Pic removed
My appologies to FastEddy For not Requesting permission to upload this pic.
That was EXACTLY what I was looking for, thank you. That really helps.
So if I were to use a E682 I don't need the dmx dongle correct? If I understand correctly (hopefully) that is a dongle and controller in one package right? So I would go from the e1.31 port on my laptop to the E682 then to my lights? I wouldn't need an SSR because power for the LED's and signals are integrated at the e682? So I run a cat5 line from the e682 to a pigtail at my lights or pixel string? I guess I could run another line (or pigtail waterproof connector) from the end of that rgb strand to another and the channel number would just pick up where the previous strand left off?
In terms of rgb flex strip, I could run a line from the e682 to the first strip, then from the end of that strip to the next strip and so on? EDIT: But if I do that then all the strings would be R,G or B all at the same time or would there be flexstrip 1, flexstrip 2, etc if they were daisy chained?
So there are different universes on the e682, each consisting of 512 channels. So I can daisy chain either flex strips or pixel stands until I reach that 512 and then move on to the next universe? Is it best to dedicate one universe to pixels and the next to rgb strands or strips? I need to research but I would assume there is a maximum power load that can be placed on each universe at well?
You are on the right track . I am not 100% certain for the dmx-rgb portion of your request with the e682 , but i assume you can use certain universes-clusters as a e1.21>dmx bridge and connect your dmx elements to that cluster .
I only have experience with the e681 and use it for pixels only .
It would be great if some one with a full understanding of how the dmx interface works on the e682 a complete a-z for dummies guide would help.
what confuses me about it is the actual connectivity , does it output to a rgb controller or can users connect rgb elements directly .
not there yet
Richard
