DMX Pixel String
 
Notifications
Clear all

DMX Pixel String

34 Posts
10 Users
0 Reactions
21.2 K Views
Posts: 859
(@smartalec)
Prominent Member
Joined: 17 years ago

I asked that orginal question on how to do the oven,
an after searching the internet here's one i found, http://www.stencilsunlimited.com/product_info.php?products_id=424&tab=specs
i figure with all the money we spend on blinky flashie, it might be worth getting a decent one an having a professional job every time.
just my (.02cent au, wich aint worth alot at the moment) 😀

cypress1138 wrote:
As far as how I am planning on soldering all this up I have been reading up on how to make your own reflow oven out of a toaster oven. Which is kind of funny because my wife has been hinting lately that she wants to get a new toaster oven 😀 I need to dig around at work because I think I've got enough pieces and parts laying around to make the controller for the oven (thermocouple, temp controller, opto-coupler, solid state relay, etc.)

Reply
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago
smartalec wrote:I asked that orginal question on how to do the oven,
an after searching the internet here's one i found, http://www.stencilsunlimited.com/product_info.php?products_id=424&tab=specs
i figure with all the money we spend on blinky flashie, it might be worth getting a decent one an having a professional job every time.
just my (.02cent au, wich aint worth alot at the moment) 😀

My two favorite methods are:
http://www.sparkfun.com/commerce/tutorial_info.php?tutorials_id=60
http://www.sparkfun.com/commerce/tutorial_info.php?tutorials_id=59


Reply
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago
aussiephil wrote:
Cypress: why not use a switch-less DMX setting process like RJ and I both do, it's simple and effective. This also allows for easy move to RDM or alt start code setting by a firmware change.

You could do both. For those that want dips that can override the dip-less addressing method when the dips are set > 0. I've done that before, if the dips are at 0 then RDM address takes over. Food for thought.


Reply
Posts: 136
(@j1sys)
Estimable Member
Joined: 17 years ago

another thought. i use mcp23s017 chips anytime i need more i/o. you can bit bang an spi interface to it (if your pic doesn't already have a spi controller) and then get 16 lines with pullups etc. for 3 pins of i/o. or use mcp23017 and do it with i2c with 2 pins.

or just use a 28 pin variant of the pic series you are using. then you have plenty of more i/o.


Reply
Posts: 84
Topic starter
(@cypress1138)
Trusted Member
Joined: 18 years ago
aussiephil wrote:Cypress: why not use a switch-less DMX setting process like RJ and I both do, it's simple and effective. This also allows for easy move to RDM or alt start code setting by a firmware change.

cheers
Aussiephil

So basically what I have gathered is that I would need to program my firmware so that when a start code of say 0x0F is received the firmware will then use the next 2 bytes as the start address of the unit. The value of 0x0F is the RDM code for DMX_START_ADDRESS... I think. Am I correct? Also, is their a specific start code that I should use to initiate setting the address?


Reply
Posts: 597
(@entropy)
Honorable Member
Joined: 19 years ago

What I haven't seen discussed (maybe I missed some reason it's not feasible?) is the classic "set start address using a program mode jumper" approach.

e.g. if the jumper is bridged, the device sets its start address based on the dimming values for devices 1 and 2 in the universe, if the jumper isn't bridged, it just uses its programmed start addy.

A single jumper is a lot easier than full-on DIPs, but this approach means you don't need to implement fullblown RDM.


Reply
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago
cypress1138 wrote:The value of 0x0F is the RDM code for DMX_START_ADDRESS... I think. Am I correct? Also, is their a specific start code that I should use to initiate setting the address?

The start code for RDM is 0xCC, you want to avoid this unless you are communicating via RDM. As far as other codes its up to you, like I said earlier you want to pick one that isn't already used by a commercial manufacturer (see the ESTA link I posted). I'm not sure what start code folks here have used...further I don't know if others verify start codes like I do (dimmer values == 0, 0 dump the values).


Reply
Posts: 84
Topic starter
(@cypress1138)
Trusted Member
Joined: 18 years ago
Entropy wrote:What I haven't seen discussed (maybe I missed some reason it's not feasible?) is the classic "set start address using a program mode jumper" approach.

e.g. if the jumper is bridged, the device sets its start address based on the dimming values for devices 1 and 2 in the universe, if the jumper isn't bridged, it just uses its programmed start addy.

A single jumper is a lot easier than full-on DIPs, but this approach means you don't need to implement fullblown RDM.

The one problem I do see with either the dip switches or a jumper is that you have to have access to the board to change either one. I would like to be able to seal up the board semi-permanently to make it water tight. If I have to break that seal every time I would like to change an address this could be a problem and this is why I was looking at the Renard protocol in the first place.

DynamoBen- Thanks for the link I missed it the first time. This will definitely help in picking an unused start code. Thanks again!


Reply
Posts: 136
(@j1sys)
Estimable Member
Joined: 17 years ago

DynamoBen -

The start code for RDM is 0x40 ...

I think RDM start code is 0xCC. who's right?

-Ed


Reply
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago
j1sys wrote:DynamoBen -

I think RDM start code is 0xCC. who's right?

-Ed

Checked the spec just now 0xCC is correct. I pulled the other number out of some old code (code that apparently didn't work). Sorry for the confusion, previous post updated.


Reply
Page 3 / 4
Share: