3 Channel DMX Modul...
 
Notifications
Clear all

3 Channel DMX Module question

13 Posts
5 Users
0 Reactions
10.4 K Views
Posts: 14
Topic starter
(@khargy)
Eminent Member
Joined: 16 years ago
[#14405]

In another thread someone recommended this 3 Channel DMX Module:

http://cheapdmx.com/1-3-channel-dmx.html

It looks promising and the price is right, but I don't see any DMX out. How do you daisy chain something like that?


12 Replies
Posts: 972
(@dmoore)
Noble Member
Joined: 17 years ago
khargy wrote:In another thread someone recommended this 3 Channel DMX Module:

http://cheapdmx.com/1-3-channel-dmx.html

It looks promising and the price is right, but I don't see any DMX out. How do you daisy chain something like that?

You can see them here - I had 80+ of them on a single RS485 output:


Reply
Posts: 14
Topic starter
(@khargy)
Eminent Member
Joined: 16 years ago
dmoore wrote:You can see them here - I had 80+ of them on a single RS485 output:

wow, very cool -- alot of stuff going on there -- I'm new to this stuff 🙂

So are you saying can I just split the DMX signal manually w/o the need for a DMX splitter?


Reply
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago
khargy wrote:
So are you saying can I just split the DMX signal manually w/o the need for a DMX splitter?

You can not split DMX, but you can daisy chain it. Most published device limits say you can chain a max of 32 devices. The actual number of devices you can chain depends on the transceivers used in each device and the distance of the chain.


Reply
Posts: 128
(@jonb256)
Estimable Member
Joined: 16 years ago

Look on EBay for RJ45 LAN Splitter.

If you crimp an RJ45 onto the leads from the 3 Channel controller, it will plug into the single jack. The DMX signal then goes "in and out" on the other side. You could probably route power over the CAT5 cable if you didn't do too many.

This isn't really a splitter done this way. More of a "T" off of the line.


Reply
Posts: 14
Topic starter
(@khargy)
Eminent Member
Joined: 16 years ago

So basically the DMX in on the module is really in and out?


Reply
Posts: 128
(@jonb256)
Estimable Member
Joined: 16 years ago

Instead of thinking of it as "in and out" think of the DMX module as just "listening," almost like a wiretap.

Since the module doesn't do any retransmitting of the signal, it will just pass on to the next module.


Reply
Posts: 972
(@dmoore)
Noble Member
Joined: 17 years ago
khargy wrote:So basically the DMX in on the module is really in and out?

There are two type of "outs" - one could be just a passive output of the 485 signal, no regeneration. Then you could have where the output regenerates the signal with a seperate 485 chip. A good example is the Lynx Express which has both outputs - a passive and a regenerated output. The $6 DMX controller has on it's board a spot for a repeater chip and a spot for the DMX output of that signal (

at :45 in if you look close) but it's not populated. So, I suspose you could get them with the repeating output but that's not the way they normally come.

But it really doesn't matter - even though the technical limit for 485 is 32 controllers, I had a total over over 90 without problem and it was NOT wired per 485 specs and yet it STILL ran just fine. So, the fact that they don't have an output is fine and it won't prevent you from chaining these controllers to others in your display.


Reply
Posts: 972
(@dmoore)
Noble Member
Joined: 17 years ago
khargy wrote:wow, very cool -- alot of stuff going on there -- I'm new to this stuff 🙂

So are you saying can I just split the DMX signal manually w/o the need for a DMX splitter?

The first thing to be aware of - DMX is only the protocol, it is RS-485 that is what you are "splitting". See my post above for an example. For a good primer on this, I've put together this:

http://www.holidaycoro.com/2010LSHWorkshop/DMX%20and%20LOR%20Protocols.pdf


Reply
Posts: 972
(@dmoore)
Noble Member
Joined: 17 years ago
DynamoBen wrote:You can not split DMX, but you can daisy chain it. Most published device limits say you can chain a max of 32 devices. The actual number of devices you can chain depends on the transceivers used in each device and the distance of the chain.

Here is a good white paper on RS485 (DMX runs over 485...as does LOR and Renard):

http://www.maxim-ic.com/app-notes/index.mvp/id/763

You can "split" if the chain is regenerated - such as in the Lynx Express.


Reply
Page 1 / 2
Share: