3 channel dip switc...
 
Notifications
Clear all

3 channel dip switch problem

12 Posts
4 Users
0 Reactions
5,926 Views
Posts: 31
Topic starter
(@cayanke)
Eminent Member
Joined: 12 years ago
[#37451]

Hi all,

I am having a problem with the 3 channel DMX dip switch controller from Holiday Coro. When I turn the power on with the DMX address set, the lights come on and stay on all blue. When I run the test patterns everything seems to work fine. I have checked and double checked the wiring and everything looks good. I have 4 of the flood kits with the 5050 modules that he sells and cannot figure out why when they are addressed they come on and stay blue.

Am I missing a step in the set up or is this something with the controller, or is it me?

Thanks for the help in advance!!!


11 Replies
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago

*Do you know for a fact you can generate good DMX with your computer? Have you set up other DMX devices successfully?

*Whose "test pattern" are you running ... the one embedded in the device or something from the computer that is generating DMX?

*Are you *sure* the wiring is OK ... getting the DMX polarity reversed is plenty easy.

*Yeah, that all-on blue thing puzzles me too ... I'm really thinking either your polarity is back asswards or your computer is not generating DMX.

HTH.

\dmc

PS: Pix of the switches would help too ... along with what channel number you think you're addressing.


Reply
Posts: 31
Topic starter
(@cayanke)
Eminent Member
Joined: 12 years ago

*Do you know for a fact you can generate good DMX with your computer? Have you set up other DMX devices successfully?

No, these are the first DMX devices I have set up. I am using the DIYLED bridge to generate the DMX from Vixen 3.1 using E1:31. I haven't got to the point where I can test for good signal to the devices bacause they are all stuck on blue unless I run through the built in tests on the controller.

*Whose "test pattern" are you running ... the one embedded in the device or something from the computer that is generating DMX?
The built in tests that are apart of the controller

*Are you *sure* the wiring is OK ... getting the DMX polarity reversed is plenty easy.
I have checked the wiring all day, but I am not sure about the real DMX signal, only that the lights do not appear to be functioning properly with just power on.

*Yeah, that all-on blue thing puzzles me too ... I'm really thinking either your polarity is back asswards or your computer is not generating DMX.
I hope I didn't screw that part up...easy to fix but haven't been able to test real DMX because of the stuck on blue part.


Reply
Posts: 31
Topic starter
(@cayanke)
Eminent Member
Joined: 12 years ago

It won't let me upload a picture for some reason, but dip 1 and 7 are on, all others are off for a start address of 65.


Reply
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago

OK, first, let's make sure you're making DMX out of the Bridge.

You should make a little DMX tester ... I always go to the "Big Clive" site for a refresher on how to do it ...

http://www.bigclive.com/dmxtest.htm

Now, of course you're doing RJ45 not XLR-5 (or even XLR-3), but the principle is the same. Pin 1 on the RJ45 is Pin 3 on the XLR-5, while Pin 2 on the RJ45 is Pin 2 on the XLR-5. Another way to look at it is that the white/orange wire is Data + and orange is Data - .

If you don't have these items handy, most Radio Shacks still carry them (you have to wade past the Sprint phones, but they're there in the back). For the RJ, I'd just buy a short Cat5 cable and cut it in half. Clive calls for 270-ohm resistors; Radio Shack has 220s, 270s and 330s; any of which will work fine (don't worry about the watts). Clive calls for a "bi-colour" LED; RS has one (called a "red/green") but if that's not in stock, you can buy two LEDs of different colors and wire them the way the circuit diagram shows (at that point it might be cheaper to buy the assortment pack, but that's your call).

Wire it up the way Clive shows and plug it into the Bridge and see what's coming out.

HTH.

\dmc


Reply
Page 1 / 3
Share: