What would it take?
 
Notifications
Clear all

What would it take?

9 Posts
8 Users
0 Reactions
3,538 Views
Posts: 793
Topic starter
(@covewi)
Noble Member
Joined: 17 years ago
[#8715]

I have an LED project that I would like to build. Its not an Xmas project but more of an art piece.

I have six rows of leds, which would make it a six dc channel circuit, I want a self contained programmed circuit that does not have to be connected to a pc and Vixen and would be enclosed in the art project.

I would need to have each row flash randomly, one at a time, for a short period of time then have them stop and light only certain rows and then repeat the process over and over again.

What would it take to design a circuit and program a board to do something like that. Suggestions were to start. Welcome private discussion using PM's

Thanks


8 Replies
Posts: 22
(@jmills)
Eminent Member
Joined: 18 years ago

I would look into the Arduino product, it should suit your needs perfectly.


Reply
Posts: 4
(@nvrdunn)
New Member
Joined: 18 years ago
jmills wrote:I would look into the Arduino product, it should suit your needs perfectly.

2nd that...

Check out this Arduino based product: http://www.seeedstudio.com/blog/?page_id=187

I'm actually working on my own LED signboard that's controlled via an arduino.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

You could start with the 8-channel Renard circuit posted on the Wiki as the basis for the controller circuit and drive standard DCSSRs or simply drive a ULN2803 driver chip. They can drive up to 500mA each but only 180mA or so when using all 6 outputs full on. If that is not enough you can double the outputs up.

OK - so now you basically have an 8-channel Renard w/DC - big deal...

Now you look around on here for someone that posted a Renard tester which is also PIC based. With that, it can send cmds to the Renard via the serial interface and you could probably program in any sequence you want into that.

Why do it this way? Well - you can use the Renard with Vixen for later reuse and everything is pretty standard components and the controller code is already written for you to handle on/off/fading...


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Some starting places might be the Arduino, Parallax or Picaxe platforms. All of these would allow you do to programming at a slightly higher level, and all have fairly large communities that could provide support in one form or another. There are probably other platforms that I haven't thought of.


Reply
mrpackethead
Posts: 2289
(@mrpackethead)
Famed Member
Joined: 19 years ago

pic 16f688 and some transisitors


Reply
Posts: 2168
(@djulien)
Noble Member
Joined: 19 years ago
covewi wrote:What would it take to design a circuit and program a board to do something like that. Suggestions were to start.

If you already have a Microchip PIC programmer, the same PIC chip that is used in the Renard controllers found on this site could be used to drive such a circuit, as could most other microcontrollers. You could adapt one of the DC SSR circuits, and then write some firmware to run the lights, then flash it into the microcontroller. It might make an interesting milearning project for microcontrollers.

Depending on how you want it to look, you might not even need the microcontroller - just use some timer circuits (such as 555s or other) to randomly light the LEDs and then delay before turning them off.

don


Reply
Posts: 793
Topic starter
(@covewi)
Noble Member
Joined: 17 years ago

I know the link to PIC programming is somewhere - ???

Is this what I need to start out?

http://www.microchipdirect.com/productsearch.aspx?Keywords=DV164120

Other suggestions?


Reply
BuzzKill
Posts: 577
(@buzzkill)
Honorable Member
Joined: 19 years ago

Arduino


Reply
Share: