Simple Renard 32
 
Notifications
Clear all

Simple Renard 32

103 Posts
25 Users
0 Reactions
56.1 K Views
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
tstraub wrote:Yea, I knew you were kidding. The truth is I already have about 3x the channel count of controllers than I plan to use. It never hurts to have a spare 😀

I think most of us have that M.O. Last year I used 192 channels. Had more than 1200 available. Geez. I just read what I typed. My wife is right. I really AM crazy!


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago

Update:
After testing the Simple Renard 32 we believe it is time to let others have a go with one of the Simple Renard series controllers. It is about as basic and low costing as you can get for a 32 channel controller that will run DC LEDs, Incandescent Lights and AC LED Light stringers. The original design is by P. Short
and PCB by Peter Rogers (Scorpia). The code and schematic has be enhanced to accommodate 32 channels, the PCB has been modified by Tyler (tstraub) for a home etch version, He is in the process of completing a final version of the PCB which we will send out for a PCB build then we will do some testing and after that is complete we will offer it to the DIYC community. We are going to start a Simple Renard 32 interest thread before we go much further into this project.
Any suggestions or criticisms are welcome.
BTW we have included the PIC code, home etch files and generic BOM, I will create a Mouser project file after the PCB is final..ATTACH]9911


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

Thanks for posting the Eagle files, it makes it easier to add my own touch. I removed the ground traces and used a flood instead. This makes it a lot quicker to do the CNC routing method that I use. The router cuts out 95% of the board just doing the ground outline. I don't think this would etch well though, since the spacing is only .o1 inches.

A question though, was there a reason that no connector was used for the AC power supply? The holes are too small for any connector pins so I'm assuming there was no intent.


Reply
tstraub
Posts: 525
(@tstraub)
Honorable Member
Joined: 18 years ago

The AC power connector is left over from Scorpia's 24 channel version. His board had a screw terminal connector and a barrel jack. There was not room to keep both connectors. I didn't have any barrel jacks on hand so I kept the screw terminal. I really didn't look too closely at the hole size because I drilled the board by hand. The screw terminal fits fine if you drill the holes slightly larger. I hope you enjoy your Simple Renard 32 and thank you for your input on the hole size I will be sure to check into that for the production boards we are trying to get done.

If you could post pictures of your CNC cut board I would like to see them.

Tyler


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

A couple of things that I noticed…

The value attribute for J6 & J10 (channel numbers) is not visible on the board and I can’t figure out how to get it to display.

The trace coming out of IC5 pin 24 on the schematic walks over pins 23, 22 & 21 below it, so it looks like it’s supposed to be connected. I moved C5, C3 & C4 above IC2 so that J10 could be moved to the right a bit.

The more that I looked at the board, the more I changed it; so it’s not really the same board that I started with. I’ve move nearly every trace.

• I pulled the parts in from the corners so that there was enough room for even the largest screw head.

• I re-routed the +5V so that the micro is no longer in the middle of supplying power to the upper and lower RJ45 jacks. The micro get’s its own power trace and each of the rows of jacks gets their own also.

• J1 & J2 were .25 mils farther from the board than all the rest of the connectors so the micro and everything to the left was moved to the right 50 mils.

• I did manage to fit the power connector on the board. I ended up turning the connector, opto and the resistors 90° and still leave plenty of room for the screw and access to it.

• When I’m done, I can upload or email this if it’s of interest.

This has been a learning experience for me. My ancient OrCad from the 80’s, no longer functions now that my PC’s are running Windows 7. Eagle has been the easiest to learn CAD system and I’ve been doing this for 25 years. I probably still am not using it in the most efficient way but it’s got a nice Undo and I’ve used it a lot.:D


Reply
Page 4 / 21
Share: