Propeller Dimmer sc...
 
Notifications
Clear all

Propeller Dimmer schematic review

66 Posts
6 Users
0 Reactions
24.1 K Views
Posts: 2630
Topic starter
(@dynamoben)
Famed Member
Joined: 19 years ago
[#7717]

The dimmer is based on the Parallax Propeller. It has a USB, DMX/RS-485, and Ethernet interface. It allows control of 32 or 64 dimmer channels. There is also an 8x2 LCD and four push buttons for a basic UI.

This is meant to be a "fully featured" dimmer. My goal wasn't to create an inexpensive dimmer since there are a number of excellent designs that already fit that need. Beyond features I really wanted to create a dimmer that anyone could customize and learn how to program.

With that being said I've posted the schematics and would like folks to review them. The only thing I'm on the fence about is opto-isolating the RS-485 interface (don't have it in there yet). Typically I would but I'm not sure if its "too much work for too little effect." Thoughts, feedback?

Go here:
http://doityourselfchristmas.com/forums/showthread.php?t=7863


65 Replies
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Just a cursory look...

1) Why are the regulator caps so big? Especially the 4700 uF cap?

2) What are the switches for?

3) What are the input voltage limits on the Propeller chip? The reason that I ask is that it appears that the LCD may pull things above the 3.3V that powers the Propeller.


Reply
mrpackethead
Posts: 2289
(@mrpackethead)
Famed Member
Joined: 19 years ago

This looks like a really interesting project. I had been doing a bit of reading about the propellor and this has got me curious enough to buy some development tools and have a tinker.

What do you recommend as a good way of getting started?


Reply
Posts: 2630
Topic starter
(@dynamoben)
Famed Member
Joined: 19 years ago
P. Short wrote:Just a cursory look...

1) Why are the regulator caps so big? Especially the 4700 uF cap?

2) What are the switches for?

3) What are the input voltage limits on the Propeller chip? The reason that I ask is that it appears that the LCD may pull things above the 3.3V that powers the Propeller.

Regulator Caps:
Yikes that is wrong...not sure what happened there. What about a set to 10uf caps, would that be better?

Switches:
The four on the LCD data lines are used to navigate the menus which set things like starting address and what not.

Input Voltages:
The Prop is a 3.3V uC however the suggested method for handling a 5V signal is a 1K-10K resistor inline or a FET. Here again if there is a better way I would love to hear it.

Opto-Isolation:
What are your thoughts on opto isolating the RS485 driver with something like 6N137?


Reply
Posts: 2630
Topic starter
(@dynamoben)
Famed Member
Joined: 19 years ago
mrpackethead wrote:This looks like a really interesting project. I had been doing a bit of reading about the propellor and this has got me curious enough to buy some development tools and have a tinker.

What do you recommend as a good way of getting started?

I don't want to get too far into the weeds but I would suggest the Propeller Education kit. Its supplied with a tutorial manual, breadboards, parts, and other fun things. If you want to go the mimimalist approach you will need the following.

Prop (dip version if you can find it)
Prop Plug (for programming, its just an FTDI FT232)
5mHz crystal
3.3V supply
24LC256 (you can go bigger)
Propeller Manual (I printed the PDF and had it spiral bound)

Go here to see the schematic: http://www.parallax.com/tabid/254/Default.aspx


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Ben,

For the caps I would think that 10uF is OK, it should meet the requirements of most, if not all, regulators.

As for the Prop/LCD, I don't see any resistors in series between the CPU and the LCD, which is what I was expecting to see. I only saw one revision of the schematic, are there others out there with the resistors in series? The series resistors probably want to be an order of magnitude smaller than the pulldown/pullup resistors already on the micro inputs.

As for the 6N137 optos, I would be inclined to include them in the design. The design is already pretty full-featured, so it would be nice to have the added safety of front-end isolation. This would increase the cost by something approaching $10, though, by the time that you add the isolating DC-DC P/S as well (perhaps using one of the VBSD1 or related parts from Digikey).


Reply
Posts: 2630
Topic starter
(@dynamoben)
Famed Member
Joined: 19 years ago
P. Short wrote:
For the caps I would think that 10uF is OK, it should meet the requirements of most, if not all, regulators.

I've made this change.

As for the Prop/LCD, I don't see any resistors in series between the CPU and the LCD, which is what I was expecting to see. I only saw one revision of the schematic, are there others out there with the resistors in series? The series resistors probably want to be an order of magnitude smaller than the pulldown/pullup resistors already on the micro inputs.

I've added a 1K resistors in series with each data line. This was a major oversight on my behalf while drawing the schematic; I have them on by breadboard...good catch!

As for the 6N137 optos, I would be inclined to include them in the design. The design is already pretty full-featured, so it would be nice to have the added safety of front-end isolation. This would increase the cost by something approaching $10, though, by the time that you add the isolating DC-DC P/S as well (perhaps using one of the VBSD1 or related parts from Digikey).

I'm fine with adding it, better safe than sorry I guess. I would much rather damage some optos than the surface mount propeller. I've not had much experience personally with isolation. Are you aware of any reference schematics I could use as a guide?


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

RPMs DMX16 controller has full isolation - might want to check that...


Reply
Posts: 2630
Topic starter
(@dynamoben)
Famed Member
Joined: 19 years ago
budude wrote:RPMs DMX16 controller has full isolation - might want to check that...

I reviewed the schematic for the DMX16 and it doesn't appear to be opto isolated.

http://doityourselfchristmas.com/forums/showthread.php?p=69633


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

woopsie - - sorry meant his DMX Dongle...
http://doityourselfchristmas.com/forums/showthread.php?t=7009


Reply
Page 1 / 7
Share: