I had not spoken to Cory and you certainly have the PCB Mfg connections. I wasn't trying to takeover anything at all. Mine started with some exchanages with Todd about a source for RGB and White LEDs. While I knew there were some issues with Pinouts changing, he did not express dissatisfaction with the supplier. You may be better than me for all of it. My concern with Direct MFG for LEDs is the lead time and qtys required.
I purchased 3 additional 48LSDs from your last group buy. These are specifically for running Floods, Strips and Specialty things such as the Snowfall tubes. So I'm in for whatever you are willing to brew.
Worst case, I assumed I would just get the LEDs myself and then go with some sort of oversized Home-etch version for the LED strips and the "FAST Brain"
dlovely wrote:So not to duplicate efforts... Altho not publicly mentioned, I was planning on running an off-site group buy for the Ren48LSD, Ren4Flood and RenFlood. Cory had mention getting any boards that came of this added since I already have the lead work done with and LED supplier. Samples have been ordered and sent to Brian for testing with his Floods. This is not the same supplier as Todd used, its a direct manufacture due to the fact Todd's supplier changed parts on him I wanted to find a MFG source to reduce change surprises. The parts for these (LEDs and PICs) are common with the above and Cory had mentioned that he uses the Ren48LSD as the triggering board I figured I could add these boards and LEDs to the off-site buy if there is interest and save people some shipping if interested in multiple items. Would also help get the White LED numbers up... Or the Red LEDs for Brian's new Red Snowfalls...
chelmuth wrote:Looking at the resistors they are in order.. 1-8 .. I used the same pins as the channel outputs for the renard software as I was originally going to mod some renard code but decided against it and rolled my own.. Maybe this schematic is easier to read?
Yes this colored version is easier to read and I can wire from it. But I don't know the correct order to place the LEDs. Am I missing something again?
I see pic pins 3and 13 go to led 1 which is top by the pic or bottom. Pic pin 3 and 12 to led 2. Pic pin 3 and 11 to led 3, ect ect to Pic pins 8 and 9 to led 28.
Is led 29 pic pin 9 and 8? Or pic pin 13 and 3? Or something else ? Or have I just had too much Lutefish?
Brian
Pin 3 to Pin 13 Forward Diode Then Reverse Diode on Same Pins
Pin 3 to Pin 12 Forward Diode Then Reverse Diode on Same Pins
Pin 3 to Pin 11 Forward Diode Then Reverse Diode on Same Pins..
Then when Down to the bottom of first column..
Pin 13 to Pin 12 Forward Diode Then Reverse Diode on Same Pins
Pin 13 to Pin 11 Forward Diode Then Reverse Diode on Same Pins
Then when done with that column
Pin 12 to Pin 11 Forward Diode Then Reverse Diode on Same Pins
Pin 12 to Pin 10 Forward Diode Then Reverse Diode on Same Pins.
Etc..
Thank you very much! I'm going to try to make three 56 LED four foot long.
Cory says that he is tired of hand-wiring the FAST controller, so here is a proposed PCB design. This is a candidate for coop buys for this season.
Here is an image of the proposed board (0.8" x 1.5"):
For reference, here are images of the LED strip (0.62" x 6.0")
and the LEDancer controller as well (1.0" x 3.0"):
Regarding the FAST controller:
1) At the moment all of the traces are on the component side, I intend to move them to the solder side.
2) basic trace width is 0.010" with .015" minimum spaciing (except for a few 0.015" traces).
3) pad size is 0.060", drill size is 0.028" for the IC, resistors and capacitor
4) pad size is 0.060", drill size is 0.036" for the connectors (I will investigate to see if this should be bigger).
You will notice that my general approach is to make the boards as small as I consider reasonable. A lot of the designs by other people spread things out a bit more, making it somewhat easier for newbies to handle and solder. Comments?
I am also thinking of making the LED-module PCB a bit wider, so that a standard 0.100" pitch connectors can be used. I'm not sure how important this is, since I think that most people will be directly soldering wires to the board, rather than using connectors. Again, any comments?



