Crazy Icicle light ...
 
Notifications
Clear all

Crazy Icicle light string idea

54 Posts
19 Users
0 Reactions
23.7 K Views
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago
P. Short wrote:Each IO pin on that PIC is good for 25 mA...

Each IO pin on that PIC is good for +/-25 mA, so each output is good for at least two channels.


Reply
Posts: 188
(@awhaley)
Estimable Member
Joined: 18 years ago

It looks like an SMD only chip... but the Philips PCA9532 is a 16 channel i2c chip with PWM all generated onboard... Or of course the TLC5940 could be used. You would then use one chip for every 2-4 strands of icicles. I think this is a great idea and could lead to some REALLY cool effects.

For a while I was thinking about a pixel thing of this sort using the 16F54 PIC... but the lack of onboard oscillator, interrupts and UART convinced me that the support components and programming difficulty would more than offset the cheap price of the chip. The 16F722 could drive 16 LEDs very easily... Renard code exists for it... it's fast enough to handle DMX if you wanted more pixels/more standard protocol....

And Peter, I've ALSO been pondering cheaper RGB pixels for quite some time! We should trade ideas at some point!

As far as control of all of this goes... I think the idea of a combination of direct control of every pixel if you want it, or a 'head unit' at the top of the chain that takes signals and then runs preprogrammed sequences on the pixels is a cool concept. I'd want access to every pixel most times...but there would be times when one channel to select and effect, a second channel to select the speed, and a third to set the color palate for the effect would be very cool. If we were doing individual pixel control of a lot of pixels, I think the next thing Vixen would need would be a pixel mapping system... LEDTRIKS uses a sort of one, so adapting to a more flexible pixel mapping system may not be all that hard!

Keep thinking on it and feel free to ask ANY questions of the group you'd like. This is a fine place to learn from step 1!

Art


Reply
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

i have been thinking about a pwm driver chip as well but is it worth replacing a $1.50 pic with a $2.70 pwm chip that still needs a pic to control it. do the advantages outweigh the disavantages?

i think the 16f722 chip could drive 16 led's quite easy and be able to do alot more.

just a thought.

ps how do you have negitive ma, surely its just a ma rating weather the pin is sinking or sourcing the power.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 19 years ago

The other idea that I've been musing over is to use a Charlie-plexed scheme with a PIC16F688. In this setup each PIC16F688 would have new firmware (perhaps using the Renard protocol) that would allow it to drive 56 LEDs. Using the Charlie-plex scheme each LED would have a 1:8 duty cycle, with up to 7 LEDs on at any given time (requiring buffer transistors for whichever LED terminals are 'common'). I'm thinking that each LED would have 32 dimmer levels, would be on/off for 26 uS (or so) at a time, and would have a 150 Hz overall refresh rate. These parameters would give good, reliable operation. It might be possible to increase the number of dimming levels if the on/off time is decreased and/or the overall refresh rate is decreased, but I think that these are becoming risky.

Under these circumstances I don't think that it would be hard to come up with firmware for this, although I'm busy on other things at the moment.


Reply
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

is it really worth the issues of charlie plexing. i mean how are you going to physically wire up 56 led's to use in a string with them charlie plexed. i would think you would be better off cutting the numbers down a bit and making the wireing less complex. sure its a few more pics but in the end i think it would be alot easier to do.


Reply
Page 3 / 11
Share: