Simple Sound to Servo - Revision history

Jklingert: /* Other Information */ added categories

2012-08-15T21:01:02Z

Other Information: added categories

← Older revision		Revision as of 21:01, 15 August 2012
Line 168:		Line 168:
	==Other Information==		==Other Information==
	A completed commercial version of Scary Terry's design with enhancements is available from [http://www.cowlacious.com/products/Scary-Terry-Audio-Servo-Driver-Board-%252d-ST400.html cowlacious] for $42.95!		A completed commercial version of Scary Terry's design with enhancements is available from [http://www.cowlacious.com/products/Scary-Terry-Audio-Servo-Driver-Board-%252d-ST400.html cowlacious] for $42.95!
			<br>

			[[Category:DIYC Controllers]]
			[[Category:DIYC Index]]

Jklingert: /* Tayda Electronics */

2012-04-07T00:10:52Z

Tayda Electronics

← Older revision		Revision as of 00:10, 7 April 2012
Line 135:		Line 135:
	<tr><td>5K OHM Trimpot Variable Resistor 6mm</td><td>R3</td><td>2</td><td>A-2513</td><td>[http://www.taydaelectronics.com/5k-ohm-trimpot-variable-resistor-6mm.html Link]</td></tr>		<tr><td>5K OHM Trimpot Variable Resistor 6mm</td><td>R3</td><td>2</td><td>A-2513</td><td>[http://www.taydaelectronics.com/5k-ohm-trimpot-variable-resistor-6mm.html Link]</td></tr>
	<tr><td>1K OHM Trimpot Variable Resistor 6mm</td><td>R6</td><td>2</td><td>A-2509</td><td>[http://www.taydaelectronics.com/1k-ohm-trimpot-variable-resistor-6mm.html Link]</td></tr>		<tr><td>1K OHM Trimpot Variable Resistor 6mm</td><td>R6</td><td>2</td><td>A-2509</td><td>[http://www.taydaelectronics.com/1k-ohm-trimpot-variable-resistor-6mm.html Link]</td></tr>
	<tr><td>10K OHM 1/4W 5% Carbon Film Resistor</td><td>R5,R12,R15,R20</td><td>20</td><td>A-2115</td><td>[http://www.taydaelectronics.com/10-x-resistor-10k-ohm-1-4w-5-carbon-film-pkg-of-10.html Link]</td></tr>		<tr><td>10K OHM 1/4W 5% Carbon Film Resistor</td><td>R5,R7,R12,R15,R20</td><td>20</td><td>A-2115</td><td>[http://www.taydaelectronics.com/10-x-resistor-10k-ohm-1-4w-5-carbon-film-pkg-of-10.html Link]</td></tr>
	<tr><td>1N914 Small Signal Diode 200mA 100V</td><td>D1</td><td>2</td><td>A-615</td><td>[http://www.taydaelectronics.com/1n914-small-signal-diode-200ma-100v.html Link]</td></tr>		<tr><td>1N914 Small Signal Diode 200mA 100V</td><td>D1</td><td>2</td><td>A-615</td><td>[http://www.taydaelectronics.com/1n914-small-signal-diode-200ma-100v.html Link]</td></tr>
	<tr><td>LM1458N LM1458 1458 IC DUAL OPERATIONAL AMPLIFIER</td><td>IC1</td><td>2</td><td>A-286</td><td>[http://www.taydaelectronics.com/lm1458n-lm1458-1458-ic-dual-operational-amplifier.html Link]</td></tr>		<tr><td>LM1458N LM1458 1458 IC DUAL OPERATIONAL AMPLIFIER</td><td>IC1</td><td>2</td><td>A-286</td><td>[http://www.taydaelectronics.com/lm1458n-lm1458-1458-ic-dual-operational-amplifier.html Link]</td></tr>

Tstraub at 23:43, 6 April 2012

2012-04-06T23:43:43Z

← Older revision		Revision as of 23:43, 6 April 2012
Line 79:		Line 79:
	## Install the 1K ohm resistor (brown-black-red) at location R1. The resistor is not polarized, so it can go either way.		## Install the 1K ohm resistor (brown-black-red) at location R1. The resistor is not polarized, so it can go either way.
	## Install the 47K ohm resistors (yellow-violet-orange) at locations R2 and R4. The resistors are not polarized, so it can go either way.		## Install the 47K ohm resistors (yellow-violet-orange) at locations R2 and R4. The resistors are not polarized, so it can go either way.
	## Install the 10K ohm resistors (brown-black-orange) at locations R5,R12,R15,R20. The resistors are not polarized, so it can go either way.		## Install the 10K ohm resistors (brown-black-orange) at locations R5,R7,R12,R15,R20. The resistors are not polarized, so it can go either way.
	## Install the 2.2K ohm resistor (red-red-red) at location R14. The resistor is not polarized, so it can go either way.		## Install the 2.2K ohm resistor (red-red-red) at location R14. The resistor is not polarized, so it can go either way.
	## Install the 470 ohm resistor (yellow-violet-brown) at location R8. The resistor is not polarized, so it can go either way.		## Install the 470 ohm resistor (yellow-violet-brown) at location R8. The resistor is not polarized, so it can go either way.

Jklingert: /* Tayda Electronics */

2012-04-01T02:50:21Z

Tayda Electronics

← Older revision		Revision as of 02:50, 1 April 2012
Line 142:		Line 142:
	<tr><td>CD4066 4066 IC CMOS QUAD BILATERAL SWITCH</td><td>IC2</td><td>2</td><td>A-555</td><td>[http://www.taydaelectronics.com/cd4066-4066-ic-cmos-quad-bilateral-switch.html Link]</td></tr>		<tr><td>CD4066 4066 IC CMOS QUAD BILATERAL SWITCH</td><td>IC2</td><td>2</td><td>A-555</td><td>[http://www.taydaelectronics.com/cd4066-4066-ic-cmos-quad-bilateral-switch.html Link]</td></tr>
	<tr><td>470 OHM 1/4W 5% Carbon Film Resistor</td><td>R8</td><td>10</td><td>A-2049</td><td>[http://www.taydaelectronics.com/10-x-resistor-470-ohm-1-4w-5-carbon-film-pkg-of-10.html Link]</td></tr>		<tr><td>470 OHM 1/4W 5% Carbon Film Resistor</td><td>R8</td><td>10</td><td>A-2049</td><td>[http://www.taydaelectronics.com/10-x-resistor-470-ohm-1-4w-5-carbon-film-pkg-of-10.html Link]</td></tr>
	<tr><td>4.7K 4K7 OHM 1/4W 5% Carbon Film Resistor</td><td>~~R4,~~R11</td><td>10</td><td>A-2027</td><td>[http://www.taydaelectronics.com/10-x-resistor-4-7k-4k7-ohm-1-4w-5-carbon-film-pkg-of-10.html Link]</td></tr>		<tr><td>4.7K 4K7 OHM 1/4W 5% Carbon Film Resistor</td><td>R11</td><td>10</td><td>A-2027</td><td>[http://www.taydaelectronics.com/10-x-resistor-4-7k-4k7-ohm-1-4w-5-carbon-film-pkg-of-10.html Link]</td></tr>
	<tr><td>50K OHM Trimpot Variable Resistor 6mm</td><td>R10,R22</td><td>4</td><td>A-2500</td><td>[http://www.taydaelectronics.com/50k-ohm-trimpot-variable-resistor-6mm.html Link]</td></tr>		<tr><td>50K OHM Trimpot Variable Resistor 6mm</td><td>R10,R22</td><td>4</td><td>A-2500</td><td>[http://www.taydaelectronics.com/50k-ohm-trimpot-variable-resistor-6mm.html Link]</td></tr>
	<tr><td>10nF 0.01uF 100V 5% Mylar Film Capacitors</td><td>C4</td><td>2</td><td>A-4106</td><td>[http://www.taydaelectronics.com/10nf-0-01uf-100v-5-mylar-film-capacitors.html Link]</td></tr>		<tr><td>10nF 0.01uF 100V 5% Mylar Film Capacitors</td><td>C4</td><td>2</td><td>A-4106</td><td>[http://www.taydaelectronics.com/10nf-0-01uf-100v-5-mylar-film-capacitors.html Link]</td></tr>

Jklingert: /* Assembly */

2012-04-01T02:06:22Z

Assembly

← Older revision		Revision as of 02:06, 1 April 2012
Line 82:		Line 82:
	## Install the 2.2K ohm resistor (red-red-red) at location R14. The resistor is not polarized, so it can go either way.		## Install the 2.2K ohm resistor (red-red-red) at location R14. The resistor is not polarized, so it can go either way.
	## Install the 470 ohm resistor (yellow-violet-brown) at location R8. The resistor is not polarized, so it can go either way.		## Install the 470 ohm resistor (yellow-violet-brown) at location R8. The resistor is not polarized, so it can go either way.
	## Install the 4.7K ohm resistors (yellow-violet-red) at ~~locations R4 and~~ R11. The resistors are not polarized, so it can go either way.		## Install the 4.7K ohm resistors (yellow-violet-red) at location R11. The resistors are not polarized, so it can go either way.
	#Install adjustment trimpots:		#Install adjustment trimpots:
	## Install the 5K ohm trimpot (502) at location R3. The trimpot only fits one way, with the two legs towards the top of the board.		## Install the 5K ohm trimpot (502) at location R3. The trimpot only fits one way, with the two legs towards the top of the board.

Jklingert at 11:55, 28 March 2012

2012-03-28T11:55:43Z

← Older revision		Revision as of 11:55, 28 March 2012
Line 1:		Line 1:
	The Simple sound to servo is an inexpensive controller based on the Scary Terry sound to servo circuit found here http://www.scary-terry.com/audioservo/audioservo.htm This circuit takes an audio source such as an MP3 player and outputs a signal to a hobby servo to move the jaw to the sound on talking props.		The Simple sound to servo is an inexpensive controller based on the Scary Terry sound to servo circuit found here http://www.scary-terry.com/audioservo/audioservo.htm This circuit takes an audio source such as an MP3 player and outputs a signal to a hobby servo to move the jaw to the sound on talking props.

	[[File:SS2S Tplace.jpg\|~~400px~~]]		[[File:SS2S Tplace.jpg\|500px]]
	[[File:Sound to servo.JPG\|~~400px~~]]		[[File:Sound to servo.JPG\|500px]]

Jklingert: /* Assembly */

2012-03-28T06:16:09Z

Assembly

← Older revision		Revision as of 06:16, 28 March 2012
Line 84:		Line 84:
	## Install the 4.7K ohm resistors (yellow-violet-red) at locations R4 and R11. The resistors are not polarized, so it can go either way.		## Install the 4.7K ohm resistors (yellow-violet-red) at locations R4 and R11. The resistors are not polarized, so it can go either way.
	#Install adjustment trimpots:		#Install adjustment trimpots:
	## Install the 5K ohm trimpot at location R3. The trimpot only fits one way, with the two legs towards the top of the board.		## Install the 5K ohm trimpot (502) at location R3. The trimpot only fits one way, with the two legs towards the top of the board.
	## Install the 1K ohm trimpot at location R6. The trimpot only fits one way, with the two legs towards the top of the board.		## Install the 1K ohm trimpot (102)at location R6. The trimpot only fits one way, with the two legs towards the top of the board.
	## Install the 50K ohm trimpots at locations R10 and R22. The trimpot only fits one way, with the two legs towards the top of the board.		## Install the 50K ohm trimpots (503) at locations R10 and R22. The trimpot only fits one way, with the two legs towards the top of the board.
	#Install the IC sockets:		#Install the IC sockets:
	## Install the 14 pin IC socket at location IC2. The notch on the socket should face the left side of the board.		## Install the 14 pin IC socket at location IC2. The notch on the socket should face the left side of the board.

Jklingert: /* BOM */

2012-03-28T05:47:48Z

BOM

← Older revision		Revision as of 05:47, 28 March 2012
Line 123:		Line 123:
	==BOM==		==BOM==

	All parts were sourced from [http://www.taydaelectronics.com Tayda Electronics] 1 BOM will populate 2 Simple Sound to Servo Boards. The BOM is a double order because just one does not meet the $5 minimum order. You will also have a few left over resistors due to the fact that Tayda requires minimum of 10 each value. The only part that I have not tested is the 3.5mm audio Jack. This jack was an after ~~though~~ and is meant to be mounted as a pass thru connector on your enclosure that way you don't need to open the enclosure to plug your audio cable in.		All parts were sourced from [http://www.taydaelectronics.com Tayda Electronics] 1 BOM will populate 2 Simple Sound to Servo Boards. The BOM is a double order because just one does not meet the $5 minimum order. You will also have a few left over resistors due to the fact that Tayda requires minimum of 10 each value. The only part that I have not tested is the 3.5mm audio Jack. This jack was an after thought and is meant to be mounted as a pass thru connector on your enclosure that way you don't need to open the enclosure to plug your audio cable in.


Line 165:		Line 165:
	The Simple Sound to Servo was designed to fit in the [http://www.aflglobal.com/cmspages/bluekey/getfile.aspx?aliaspath=/productlist/Product-Lines/Optical-Connectivity---Apparatus/Terminal-Access-TA-200-205-Terminal-Enclosure/doc/TA-200-Terminal-Enclosure TA-200 Demarcation Enclosure] available from numerous vendors including [http://wlcventures.com/zencart/index.php?main_page=index&cPath=1\| www.wlcventures.com]<br/>		The Simple Sound to Servo was designed to fit in the [http://www.aflglobal.com/cmspages/bluekey/getfile.aspx?aliaspath=/productlist/Product-Lines/Optical-Connectivity---Apparatus/Terminal-Access-TA-200-205-Terminal-Enclosure/doc/TA-200-Terminal-Enclosure TA-200 Demarcation Enclosure] available from numerous vendors including [http://wlcventures.com/zencart/index.php?main_page=index&cPath=1\| www.wlcventures.com]<br/>
	[[File:TA-200.jpg\|100px]]<br/>		[[File:TA-200.jpg\|100px]]<br/>


	==Other Information==		==Other Information==
	A completed commercial version of Scary Terry's design with enhancements is available from [http://www.cowlacious.com/products/Scary-Terry-Audio-Servo-Driver-Board-%252d-ST400.html cowlacious] for $42.95!		A completed commercial version of Scary Terry's design with enhancements is available from [http://www.cowlacious.com/products/Scary-Terry-Audio-Servo-Driver-Board-%252d-ST400.html cowlacious] for $42.95!

Jklingert at 05:36, 28 March 2012

2012-03-28T05:36:03Z

← Older revision		Revision as of 05:36, 28 March 2012
Line 6:		Line 6:

	==Adjustments==		==Adjustments==
	'''Gain:'''		'''Gain: R3'''
	The gain adjustment is used to control the gain of the amplifier to match the controller to your source audio		The gain adjustment is used to control the gain of the amplifier to match the controller to your source audio

	'''Threshold:''' The threshold adjustment is used to calibrate the circuit and set the point of sound or no sound		'''Threshold: R6''' The threshold adjustment is used to calibrate the circuit and set the point of sound or no sound

	'''Max Adj:'''		'''Max Adj: R22'''
	The max adjust is used to set the maximum servo position when sound is present. You can think of this like a high limit switch		The max adjust is used to set the maximum servo position when sound is present. You can think of this like a high limit switch

	'''Min Adj:'''		'''Min Adj: R10'''
	The min adjust is used to set the minimum servo position when sound is not present. You can think of this like a low limit switch.		The min adjust is used to set the minimum servo position when sound is not present. You can think of this like a low limit switch.

	'''Capacitor Select:'''		'''Capacitor Select: JP4,JP5,JP6'''
	There are 3 capacitors of different values to chose from. The higher the value of the capacitor the more smooth the jaw will move. If you want a more jerky action enable a lower value capacitor or no capacitor at all. The capacitors are arranged lowest to highest value from left to right. Capacitors are enabled by placing a shunt on the jumpers JP4,JP5,JP6 directly above the capacitors.		There are 3 capacitors of different values to chose from. The higher the value of the capacitor the more smooth the jaw will move. If you want a more jerky action enable a lower value capacitor or no capacitor at all. The capacitors are arranged lowest to highest value from left to right. Capacitors are enabled by placing a shunt on the jumpers JP4,JP5,JP6 directly above the capacitors.

Line 23:		Line 23:
	The LED lights up when sound is present and is used to aid in setting the threshold adjustment		The LED lights up when sound is present and is used to aid in setting the threshold adjustment

	'''L/R Select:'''		'''L/R Select: JP1,JP2'''
	If you want the board to "Listen" only to the left or right channel of audio install a shunt on either the left or right jumper. If you want it to "listen" to both channels install shunts on both jumpers.		If you want the board to "Listen" only to the left or right channel of audio install a shunt on either the left or right jumper. If you want it to "listen" to both channels install shunts on both jumpers.

Line 165:		Line 165:
	The Simple Sound to Servo was designed to fit in the [http://www.aflglobal.com/cmspages/bluekey/getfile.aspx?aliaspath=/productlist/Product-Lines/Optical-Connectivity---Apparatus/Terminal-Access-TA-200-205-Terminal-Enclosure/doc/TA-200-Terminal-Enclosure TA-200 Demarcation Enclosure] available from numerous vendors including [http://wlcventures.com/zencart/index.php?main_page=index&cPath=1\| www.wlcventures.com]<br/>		The Simple Sound to Servo was designed to fit in the [http://www.aflglobal.com/cmspages/bluekey/getfile.aspx?aliaspath=/productlist/Product-Lines/Optical-Connectivity---Apparatus/Terminal-Access-TA-200-205-Terminal-Enclosure/doc/TA-200-Terminal-Enclosure TA-200 Demarcation Enclosure] available from numerous vendors including [http://wlcventures.com/zencart/index.php?main_page=index&cPath=1\| www.wlcventures.com]<br/>
	[[File:TA-200.jpg\|100px]]<br/>		[[File:TA-200.jpg\|100px]]<br/>


			==Other Information==
			A completed commercial version of Scary Terry's design with enhancements is available from [http://www.cowlacious.com/products/Scary-Terry-Audio-Servo-Driver-Board-%252d-ST400.html cowlacious] for $42.95!

Jklingert: /* Schematic */

2012-03-28T05:17:32Z

Schematic

← Older revision		Revision as of 05:17, 28 March 2012
Line 115:		Line 115:
	==Schematic==		==Schematic==

	Here is a schematic diagram in pdf format ~~[[File:Simple Sound to Servo sch~~.~~pdf]]~~		Here is a [http://doityourselfchristmas.com/wiki/images/1/19/Simple_Sound_to_Servo_sch.pdf schematic diagram] in pdf format.

	==Board==		==Board==