Assembly Instructions For The REN 32 - Revision history

Jklingert: /* Disclaimers */

2013-08-05T14:09:05Z

Disclaimers

← Older revision		Revision as of 14:09, 5 August 2013
Line 1:		Line 1:
	==Disclaimers==		==Disclaimers==
	The standard disclaimers pertaining to the information contained on this wiki page are listed [[Disclaimers \| here.]]<br/>		The standard disclaimers pertaining to the information contained on this wiki page are listed [[Disclaimers \| here.]]<br/>
	~~'''THIS BOARD IS STILL IN DEVELOPMENT AND SUBJECT TO CHANGE.'''<br>~~		'''THIS WIKI PAGE IS NOT COMPLETE YET.'''<br>
	'''THIS WIKI PAGE IS NOT COMPLETE YET ~~AND HAS NOT BEEN CHECKED FOR ERRORS~~.'''<br>


	==Board Assembly==		==Board Assembly==

Dlovely: /* Board Assembly */

2013-07-17T17:42:52Z

Board Assembly

Show changes

Jklingert: /* Board Assembly */

2013-06-20T21:37:30Z

Board Assembly

← Older revision		Revision as of 21:37, 20 June 2013
Line 94:		Line 94:
	\|-		\|-
	\|		\|
	* '''17''' <span style="font-size:21px">□</span> - Install two fuse clips (PN# 534-3517) '''Note: they are directional for proper fit of the fuse.''' A helpful installation tip here would be to put a fuse in the clips when you position them in their mounting holes. This will help keep them correctly aligned so that the fuse will fit properly.		* '''17''' <span style="font-size:21px">□</span> - Install two fuse clips (PN# 534-3517) '''Note: they are directional for proper fit of the fuse.''' A helpful installation tip here would be to put a fuse in the clips when you position them in their mounting holes. This will help keep them correctly aligned so that the fuse will fit properly. Examine them carefully, as they often have extra bends that should be placed on the outside end, to stop the fuse from slipping out. Be careful, the fuse holders require a fair amount of solder and heat to attach them. The FUSE should not be present when installing the clips, as the extra heat may melt the end of the fuse.
	\|\| [[File:Fuse Clip.png \| 50px]] [[File:REN32-STEP17.jpg \| 200px]]		\|\| [[File:Fuse Clip.png \| 50px]] [[File:REN32-STEP17.jpg \| 200px]]
	\|-		\|-
Line 187:		Line 187:

	<center>'''Congratulations! You have finished building your REN 32!'''</center>		<center>'''Congratulations! You have finished building your REN 32!'''</center>


	==Mounting the REN 32 in an Enclosure==		==Mounting the REN 32 in an Enclosure==

Jklingert: /* Related Links */

2013-06-20T21:35:23Z

Jklingert: /* Mounting the REN 32 in an Enclosure */

2013-06-20T21:29:53Z

Mounting the REN 32 in an Enclosure

← Older revision		Revision as of 21:29, 20 June 2013
Line 190:		Line 190:

	==Mounting the REN 32 in an Enclosure==		==Mounting the REN 32 in an Enclosure==
	:		:The REN 32 has mounting holes that line up with the standoffs in the common enclosures like the [[Enclosures#CG-500_.28CableGuard_500_Coax_Demarcation_Enclosure.29\| CG-500]], [[Enclosures#CG-1000_.28CableGuard_1000_Coax_Demarcation_Enclosure\| CG-1000]] and the [[Enclosures#CG-1500_.28CableGuard_1500_Coax_Demarcation_Enclosure.29\| CG-1500]].
			[[File:REN32-ENCLOSURE.jpg \| 500px]]

	==Parts Listing (BOM)==		==Parts Listing (BOM)==

Jklingert: /* Board Assembly */

2013-06-20T21:24:29Z

Board Assembly

← Older revision		Revision as of 21:24, 20 June 2013
Line 187:		Line 187:

	<center>'''Congratulations! You have finished building your REN 32!'''</center>		<center>'''Congratulations! You have finished building your REN 32!'''</center>


			==Mounting the REN 32 in an Enclosure==
			:

	==Parts Listing (BOM)==		==Parts Listing (BOM)==

Jklingert: /* Board Assembly */

2013-06-20T21:18:24Z

Board Assembly

← Older revision		Revision as of 21:18, 20 June 2013
Line 128:		Line 128:
	\|\| [[File:REN32-STEP24.jpg \| 200px]]		\|\| [[File:REN32-STEP24.jpg \| 200px]]
	\|-		\|-
	\|<blockquote> If you are unsure about your ability to build this board, then you should go to [[Beginners Setup Guide The ~~Renard SS24~~ \| The Beginner's Setup Guide]] at this point. [[Beginners Setup Guide The ~~Ren32~~ \| The Beginner's Setup Guide]] will walk you thru some initial tests to make sure that everything is working correctly before inserting the IC chips. </blockquote>		\|<blockquote>''' If you are unsure about your ability to build this board, then you should go to [[Beginners Setup Guide For The REN 32 \| The Beginner's Setup Guide]] at this point. [[Beginners Setup Guide For The REN 32 \| The Beginner's Setup Guide]] will walk you thru some initial tests to make sure that everything is working correctly before inserting the IC chips.''' </blockquote>
	\|-		\|-
	\|<center>'''INSTALLATION NOTE:''' </center>		\|<center>'''INSTALLATION NOTE:''' </center>

Jklingert: /* Board Assembly */

2013-06-20T20:40:34Z

Board Assembly

← Older revision		Revision as of 20:40, 20 June 2013
Line 27:		Line 27:
	\|		\|
	* '''2''' <span style="font-size:21px">□</span> - Install four diodes D1 thru D4 (PN# 625-1N5817-E3). The diodes will have a silver/grey stripe on a black body. Make sure that this stripe lines up with the stripe on the PCB silk screen (to the left).		* '''2''' <span style="font-size:21px">□</span> - Install four diodes D1 thru D4 (PN# 625-1N5817-E3). The diodes will have a silver/grey stripe on a black body. Make sure that this stripe lines up with the stripe on the PCB silk screen (to the left).
	\|\| [[File:REN32-STEP2.jpg \| 200px]]		\|\| [[File:REN32-POWER-DIODE.jpg \| 100px ]] [[File:REN32-STEP2.jpg \| 200px]]
	\|-		\|-
	\|		\|
Line 47:		Line 47:
	\|		\|
	* '''7''' <span style="font-size:21px">□</span> - Install zener diode D5 (PN# 78-1N5229B). The diode must be installed correctly. The diode should have a black stripe on the orange/red body. Make sure that this stripe lines up with the stripe on the PCB silkscreen (to the left).		* '''7''' <span style="font-size:21px">□</span> - Install zener diode D5 (PN# 78-1N5229B). The diode must be installed correctly. The diode should have a black stripe on the orange/red body. Make sure that this stripe lines up with the stripe on the PCB silkscreen (to the left).
	\|\| [[File:REN32-STEP7.jpg \| 200px]]		\|\| [[File:REN32-SIGNAL-DIODE.jpg \| 100px ]] [[File:REN32-STEP7.jpg \| 200px]]
	\|-		\|-
	\|		\|
	* '''8''' <span style="font-size:21px">□</span> - Install zener diode D6 (PN# 78-1N5239B). The diode must be installed correctly. The diode should have a black stripe on the orange/red body. Make sure that this stripe lines up with the stripe on the PCB silkscreen (to the right).		* '''8''' <span style="font-size:21px">□</span> - Install zener diode D6 (PN# 78-1N5239B). The diode must be installed correctly. The diode should have a black stripe on the orange/red body. Make sure that this stripe lines up with the stripe on the PCB silkscreen (to the right).
	\|\| [[File:REN32-STEP8.jpg \| 200px]]		\|\| [[File:REN32-SIGNAL-DIODE-RIGHT.jpg \| 100px ]] [[File:REN32-STEP8.jpg \| 200px]]
	\|-		\|-
	\|		\|

Jklingert: /* Board Assembly */

2013-06-20T20:32:51Z

Board Assembly

← Older revision		Revision as of 20:32, 20 June 2013
Line 59:		Line 59:
	\|<center>'''INSTALLATION NOTE:''' </center>		\|<center>'''INSTALLATION NOTE:''' </center>
	<blockquote>The following resistor network is a "bussed" type resistor network. This means that the five resistor components (pins 2-6) are all connected in a common buss to pin 1. Installing the resistor network backwards will cause a multitude of malfunctions. So please take the time to make sure it is installed correctly.</blockquote>		<blockquote>The following resistor network is a "bussed" type resistor network. This means that the five resistor components (pins 2-6) are all connected in a common buss to pin 1. Installing the resistor network backwards will cause a multitude of malfunctions. So please take the time to make sure it is installed correctly.</blockquote>
			\|\|[[File:REN32-RESISTOR.jpg \| 200px]]
	\|-		\|-
	\|		\|
Line 121:		Line 122:
	\|		\|
	* '''23''' <span style="font-size:21px">□</span> - Install the transformer TF1 (PN# 838-3FD-412). It is important that you get the correct orientation for the transformer. The legs of the transformer are numbered on the base plastic. You must have pins 1-4 on the left side of the board when the transformer is installed.		* '''23''' <span style="font-size:21px">□</span> - Install the transformer TF1 (PN# 838-3FD-412). It is important that you get the correct orientation for the transformer. The legs of the transformer are numbered on the base plastic. You must have pins 1-4 on the left side of the board when the transformer is installed.
	\|\| [[File:REN32-TRANSFORMER.jpg \| ~~200px~~]][[File:REN32-STEP23.jpg \| 200px]]		\|\| [[File:REN32-TRANSFORMER.jpg \| 100px]] [[File:REN32-STEP23.jpg \| 200px]]
	\|-		\|-
	\|		\|

Jklingert: /* Board Assembly */

2013-06-20T20:01:36Z

Board Assembly

← Older revision		Revision as of 20:01, 20 June 2013
Line 156:		Line 156:
	\|}		\|}

			:'''JP1 & JP2 Configuraton'''

			:The configuration of JP1 and JP2 depends on the type of communication being used:
			<br>

			::'''RS-232 Communication (direct connect to PC)'''
			:::*'''JP1''' installed
			:::*'''JP2''' not installed

			:::Reminder: This only applies to the first Renard SS board connected to the PC. The output of a Renard SS board to the next board is RS-485.
			<br>

			::'''RS-485 Communication (output of a Renard board or output from a RS-485 adapter/converter)'''
			:::*'''JP1''' not installed
			:::*'''JP2''' installed (try removing if data communication issues are encountered)
			<br>

			:'''JP3 Configuraton'''

			::*Installed when running the Diagnostics Firmware
			::*Normally not installed when running the Operational Firmware. But can be left installed if you don’t mind seeing the on-board LEDs responding with the associated channels.

← Older revision		Revision as of 21:35, 20 June 2013
Line 313:		Line 313:
	:[[Beginners Setup Guide For The REN 32]]		:[[Beginners Setup Guide For The REN 32]]

	:[[~~Troubleshooting_Guide_The_REN_32~~\| Troubleshooting Guide The REN 32]]		:[[Troubleshooting_Guide_For_The_REN_32\| Troubleshooting Guide For The REN 32]]

	:Board Availability Information]		:Board Availability Information]