T.D.Sutton
T.D.Sutton
@t-d-sutton
Honorable Member
Joined: Oct 15, 2009
Topics: 71 / Replies: 374
Reply
RE: Merry Christmas Sign

Regarding blackout of individual LED's, I use 5.0 mm or 6.0 mm internal diameter normal heatshrink and pinch the free end when it is still "hot", work...

10 years ago
Forum
Reply
RE: RenTester - any interest?

ctmal wrote:Everything is in the download. It was created in Kicad(which is free) so you should be able to load it up and get whatever you need from ...

10 years ago
Forum
Reply
RE: RenTester - any interest?

Hi Chris, I see the thread has been resurrected 🙂 is there perchance a schematic of the circuit in existance, PDF, Jpg, etc ?? so I could happil...

10 years ago
Forum
Reply
RE: How to roll up wire and cables for storage

After 50 yrs or so of using that method 🙂 I jokingly tell folks that I got my "Degree" in cable winding in 1963, when working as an outside broadca...

10 years ago
Reply
RE: New RenServo version 2 firmware

ctmal wrote:Ok, I'll work on it this week. How do you feel about being a guinea pig? I don't have a basic renards to do any testing. Actually the...

10 years ago
Forum
Reply
RE: New RenServo version 2 firmware

ctmal wrote:I took a look and it appears I left the OUTPUT_NEGATIVE_TRUE in there for the led's(if you choose this option) but I didn't put it in the...

10 years ago
Forum
Reply
RE: Reducing the range of my transmitter - Yes strange I know.

pakeonoahu wrote:I have couple of those transmitter, I am not sure lowering voltage will help/possible, it has no transistor on final stage, antenna i...

10 years ago
Forum
Reply
RE: Reducing the range of my transmitter - Yes strange I know.

Barnabybear wrote:Hi, all thanks for the comments. I'm going to try dropping the supply voltage first as thats an easier of the two for me (I don't kn...

10 years ago
Forum
Reply
RE: Reducing the range of my transmitter - Yes strange I know.

Hi My 0.02c worth, I agree, a pad is the way to go, three resistors in a "T" or "Pi" configuration will work brilliantly, I would mount it in a metal ...

10 years ago
Forum
Reply
RE: New RenServo version 2 firmware

Thanks Chris, I will keep you posted 🙂 I just have to wait for the adaptor boards to arrive to mount the SOIC PIC16f1825's that I purchased in ...

10 years ago
Forum
Reply
RE: New RenServo version 2 firmware

That is great news Chris, with this software running off the internal oscillator in the "Pic", do I assume that the board I have just constructed with...

10 years ago
Forum
Reply
RE: Mounting strobes

Chris, I just put them on the "light holders", in my case old steel Gazebo frame tube, with a few inches spare and let them lie to one side of the "l...

10 years ago
Reply
RE: Heatgun vs Butane Torch for Heatshrink

I use a cheap "Paint Stripper" heat gun, and would not be without it. I found the Butane flame throwers too easy to burn the insulation and the heat s...

10 years ago
Forum
Reply
RE: Back surgery

One of those round latex cushions that look like a large donut, with a centre hole, work great to support your back when sitting, place the "Hole" ove...

10 years ago
Reply
RE: Tune to sign question?

gassy wrote:Not sure how others do it, but I just make my sign another element in each of my sequences and control it just like any other element. "...

10 years ago
Forum
Page 9 / 30