Merry Christmas all! I am playing with some small matrices 3x20 on pilings in front of the house. This is my first use of the matrix setup elements in V3 and I am missing something. They are all patched and setup in the preview using the matrix tools. In preview the effects like wipe or fire look correct but in real life the individual columns alternate rather than all going together. For example, a vertical wipe has columns 1 and 3 going up but column 2 goes down. Same with the fire effect. I was reading around here and saw a reference to the "reverse order" patching option. Is this what I need to do in patching to get these aligned right? Vixen created the sub-groups C1, C2 and C3 for me during setup so do I need to apply a reverse patch to C2? And if so, do I have to do every column individually or am I missing that piece of magic that does it all at once? I would hate to think of doing this on a large matrix that I know many folks have. These are single pixel strings, 60 pixels and built with the zig zag option at 20. In preview the bottom pixel in each column corresponds to the #1 pixel in the element so I am pretty sure this is a patching issue. Cheers!
Either do it in the patching or in the controller if it has Zig-Zag feature.
You can patch the whole element then go back and do the reverse on only the ones that need it.
So if C2 neews to be reversed. click on it then do the show where patched. it will highlight them in the controller. unpatch controller.
then check the reverse button and patch them right back. Easier but still takes time.
rayhjr wrote:
Either do it in the patching or in the controller if it has Zig-Zag feature.
You can patch the whole element then go back and do the reverse on only the ones that need it.
So if C2 neews to be reversed. click on it then do the show where patched. it will highlight them in the controller. unpatch controller.
then check the reverse button and patch them right back. Easier but still takes time.
Aye. I will go ahead and do this. The controller (ESPixelstick) does not have zig zag and the display setup step in V3 did not seem to care if I checked that box or not. Thanks!
Esps v4 has zig zag
MartinMueller2003 wrote:
Esps v4 has zig zag
Well hush my mouth, I see it now! Thanks Martin I will give it a try.
Zig Zag is also an option when using the Matrix creation tools in Vixen. If you setup that when creating it, it will create the necessary zig zag patching order and when you patch it will be automatically patched. So there are several options between the controllers and setup. You just have to decide which one works best for you.
jeffu231 wrote:
Zig Zag is also an option when using the Matrix creation tools in Vixen. If you setup that when creating it, it will create the necessary zig zag patching order and when you patch it will be automatically patched. So there are several options between the controllers and setup. You just have to decide which one works best for you.
Thanks. I will play around with that as well. Problem is I patched first then realized I needed the zig zag. I might rebuild the actual elements to better support the patching too. In my current build each column starts top left, goes down up then down. Then I have an extension to the next column top left so patching as one matrix using zig zag breaks it. (Current design would be up-down-up-up-down-up and so on) I may just repatch in Vixen and use the reverse order feature on the middle column of each one. Amazon just sent me a new outdoor AP so I have some fun and games planned for tomorrow! 😁
You can also define your own custom patching order in the Display Setup. Select the Matrix top level and then in the bottom left dropdown choose Patching Order. A dialog will open and allow you to drag the elements into the proper order. You can also select blocks and right click to reverse or zig zag groups of them. This defines the patching order once to you don't have to keep messing with it if you want to move from one controller to another or a different place on the controller.
When you set the zig zag or other options for order in the Matrix/Grid setup, it does this under the covers. But you can do it yourself or edit it if you need to adjust parts of it that the setup wizard can't accommodate.
jeffu231 wrote:
You can also define your own custom patching order in the Display Setup. Select the Matrix top level and then in the bottom left dropdown choose Patching Order. A dialog will open and allow you to drag the elements into the proper order. You can also select blocks and right click to reverse or zig zag groups of them. This defines the patching order once to you don't have to keep messing with it if you want to move from one controller to another or a different place on the controller.When you set the zig zag or other options for order in the Matrix/Grid setup, it does this under the covers. But you can do it yourself or edit it if you need to adjust parts of it that the setup wizard can't accommodate.
Thanks Jeff. This may make it easier and more sensible to leave the physical build as is and just adjust via patching.
Just an update for anyone finding this in a future search. I went ahead and used the custom patching order choice from Display Setup. I then unpatched and repatched without any additional changes or adjustments to the controller or patching. It seems to working perfectly now!
As an added benefit I setup a new outdoor AP and solved the delay issue I was getting on my yard elements so today was a win win! Nothing like working out display kinks on the 29th of December. 😎
Thanks for the great advice!

