I am running ver 2.1. I have 3 houses in my program. Using com port 1 for half of my yard. USB To serial converter for the other two com ports. Com port 2 for one of my neighbors house. Com port 4 for the other half of my yard and my other neighbor. Everything for my house on port 1 and 4 has been running flawlessly for a week. Hooked one of the neighbors on my last renard board tonight, and only the last 3 channels on his first board work. Put a spare controller in and it does the same thing. Put a spare controller right next to my last board with a 6 foot cat 5 cable and it does the same thing. Using the programs plug in setup. Checked baud rates on plug in setup and in device manager for all ports and they look right. I stumped! Worst part is we enter the lighted contest every year and judging was tonight. Of course my neighbors waited until the last day to put their stuff up too! Any suggestions?
A little more info on this. I am using Renard SS24 boards only. I have 14 total. Com 1 has 4 boards, running flawlessly. Com 2 has 6 boards. Only the first 4 are working correctly. I have tried swapping out the last 2 boards with a spare and it does the same thing. I may have a cable issue here, need to check that tonight. Com 4 has 3 boards at my house, and 3 at my neighbors house. My 3 are working perfectly, only getting the last 3 channels on his first board working. I have tried swapping my last board, and his first board, and it does the same thing. My sequencing looks correct. Baud rates look right in device manager for USB to serial converters. I am going to try swapping cables to different com ports and see what happens tonight. Any other ideas? I am obviously getting data out on com 4 to my neighbors house, but only last 3 channels are working, but they are working correctly. Help!
Ok, let's divide and conquer here. It sounds like you have 2 issues(which may or may not be related....). Com 2 had 4 boards working and 2 not, and Com 4 has 3 boards working, 1 board partially and 2 boards off.
Com 2: Since you mentioned it might be a communications issue,
1: Swap controllers #4 and #5 and see if that changes anything - testing the output on controller 4 here.
2: Swap the network cable between #4 and #5 and place it between #3 and #4 and see if that changes things - ruling out the network cable here.
I'm going to separate the com ports into different posts.
I swapped those already. Card #4 works fine, still nothing on Card #5. Haven't checked the cable yet. I have a cat 5 tester at work I am bringing home tonight to test cables.
I rebuilt my profile and detached all my sequences today to see if I had a corrupted profile. Will try that tonight also.
Here is what I was going to continue with but I had problems connecting suddenly.
Com 4:
Ok, I'm assuming you're set up as your controllers are #1, #2 and #3 and your neighbors are #4, #5 and #6.
1: Start by just trying to get #4 working. Swap controllers #3 and #4 and see what(if anything) changes.
2: If the results are exactly the same as they were, I would try swapping cat 5 cables from between #2 and #3 to between #3 and #4 since that could quickly rule out the cabling.
3: If everything is still the same, I'd start to suspect you plugin setup and/or channel ordering:
a) Can you post how you have the channel setups in your 3 Renard plugins?
b) In Vixen, right click the channels to the left and select toggle channel numbers. Look at the channels in your neighbors yard. Make sure they look right(i.e., if this port run starts at 1, your neighbors house would have to be between 73 and 144).
c) What happens in Vixen if you use the Test channels button in the upper left hand corner and try to turn on port 1 of controller 4...If that works, keep scrolling until you see something off and let us know.
