Thoughts on a possi...
 
Notifications
Clear all

Thoughts on a possible setup

16 Posts
5 Users
0 Reactions
4,559 Views
Posts: 110
Topic starter
(@corydorning)
Estimable Member
Joined: 13 years ago
[#43611]

So in doing some R&D, I'm realizing there's lots of right ways to setup a Christmas display but there also seems to be a lot of things that can go wrong. As a beginner, I'd like to avoid these pitfalls. I'm getting a late start this year, but I'm also just doing a simple project to familiarize myself with this hobby. To start, I'm just focusing on a pixel matrix this year.

So, here was my plan and its based primarily around simplicity and maximizing the Falcon F16V2-R Controller, even if it means it isn't the most cost effective. I'm obviously not looking to throw money away, but as I ease into this, simplicity and expandability take priority.

--UPDATED BASED ON FEEDBACK BELOW - PLEASE CALL OUT ANY POSSIBLE ISSUES YOU SEE --

Proposed controller setup:
- Controller will be powered by 2 600w power supplies, 8 outputs each
- Each output will power the first 110 pixels (8 outputs x 110 pixels x .6w/pixel = 528w)
- Raspberry Pi will also be powered by the Controller
- All contained in single enclosure

Proposed power injection setup:
- Up to 5 additional strands of 114 pixels each, per controller output (connected to the first strand of 110 pixels, which are being powered by the controller)
-- This totals 680 pixels per output which is the Falcon F16's max per output
-- This seemingly works well with a 360w power supply (114 pixels x 5 strands x .6w = 342w)
- Enclosures with 360w power supplies placed strategically for power injection, using 14/2 cord
- T-splitters used for power injection (power cord on first strand will be capped as to not cross power supplies)

Following these rules, I should theoretically never have to worry about overpowering anything.

QUESTIONS
---
Does all of this seem to add up? Anything I'm missing?

What are your recommendations for sending the power and data signal to the first 110 pixels for each output? (Since the controller is central to the entire system, the cable runs to the first 120 pixels of each output will vary greatly - 10ft to 80ft).

Any feedback is appreciated.


15 Replies
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago

Have you already purchased the equipment already?

Right now, the Falcon boards are out of stock, they should have some in and start shipping by Dec 14, Of course if you are ordering nodes from Ray at this time they probably will not get here until then too so...

You may want to think about sourcing pixels stateside, and may need to look at different controllers.


Reply
Posts: 110
Topic starter
(@corydorning)
Estimable Member
Joined: 13 years ago

I already have everything I need. Just trying to figure a simple and expandable setup going forward.


Reply
Posts: 911
(@madsci1016)
Noble Member
Joined: 12 years ago

It sounds like you went 5V, and with 5V you won't get strings of 120 pixels without power injection. Safe rule of thumb is 50 pixels per power point. So you can run a string of 100 pixels if you inject power at both ends. 120 is risky but possible. You may have to turn brightness down a hair if you aren't happy with the whites.

the cable runs to the first 120 pixels of each output will vary greatly (10ft to 80ft or so).

You also can't send data much more than 10-15' without null pixels.

Shame you already bought the F16, i would have suggested an f4 for half the cost. You could have used 4 ports for your gird, and then with a differential expander run other elements around your yard as well.

You should draw out how you plan to wire this grid and post it. I think there's a few things you need to watch out for.


Reply
Posts: 110
Topic starter
(@corydorning)
Estimable Member
Joined: 13 years ago

I went 12v, sorry. fixed original post. I went with the f16 so i could run everything with just it (with some possible add-ons obviously).


Reply
Page 1 / 4
Share: