Surprised Newb
 
Notifications
Clear all

Surprised Newb

17 Posts
9 Users
0 Reactions
7,694 Views
Posts: 13
Topic starter
(@nanowit)
Active Member
Joined: 19 years ago
[#1424]

Last year about this time someone sent me an email with a link to a video of a Christmas light display set to music. I received a reply from someone else who received it and they said the video looked like it was doctored up on someones editing system, it looked fake.
This week I received my December issue of Nuts & Volts and there is an article by Jon Williams titled "Vixen lights the way." I read the article with interest but it didn't go into any detail about controllers or SSRs or any of the stuff in the field, just a get started guide for Vixen. One of the resources was the Vixen site which eventually led me here. Wow, it wasn't a fake video and you don't have to have just won the lotto to do this.... I think I'm getting hooked.

So, here is my situation:
I have plenty of room for a display, my front yard is big. The fence is 150' from the house and I have one 20 amp circuit at the gate.
I have been in electronics for quite a while and have designed and etched circuit boards although I am over that thrill and would prefer to buy an etched and drilled board if not too expensive. From what I have read so far I would probably start with a Renard 64 or something like that and a couple of SSRs to start out.

Here are my questions:
I am assuming that everything can be connected together via CAT-5 cable. What are the length limitations between the PC and the controller and between the controller and the SSRs?

Is there a block diagram somewhere that shows a typical set up of this type?

Is there a source for etched and drilled boards?

What kind of speakers are commonly used for the outdoor sound?

I have never seen a computer controlled Christmas display except in the Youtube type videos online. Does anyone know of any in or near Palm Beach County, Florida?

Hope that's not too many questions a once.
Ron


16 Replies
Posts: 156
(@walden)
Estimable Member
Joined: 19 years ago

Usually you don't use speakers to let them hear your music, you can buy an FM transmitter to broadcast your signal to there car stereos.

Also wjohn can hook you up with boards and what not if he has any in stock.


Reply
Posts: 529
 Josh
(@josh)
Honorable Member
Joined: 19 years ago

if you want to run speakers, if the neighbors are cool with it., I have ran normal pc speakers for two years no problem, even with ice and snow on the speakers. Now the best bet is to run something for outdoor use. They sell really nice rock looking speakers that you place near your sidewalk or where fits.

As far as boards, wjohn has them, i will post a rundown of prices in my next post...


Reply
Posts: 529
 Josh
(@josh)
Honorable Member
Joined: 19 years ago

A GRINCH shipped is 15.83

2 GRINCHs shipped is 23.09

A GRINCH and 8 SSRs shipped will cost (USD) 32.40

A GRINCH and 16 SSRs shipped will cost (USD) 44.82

A REN64 and 16 SSRs shipped will cost (USD) 46.38

2 GRINCH and 32 SSRs shipped will cost (USD) 76.92

2 REN64 and 32 SSRs shipped will cost (USD) 80.30

A LEDTRIKs PCB, Shipped to the US USD$16.87

2 LEDTRIKs PCBs, Shipped to the US USD$25.15


Reply
Posts: 529
 Josh
(@josh)
Honorable Member
Joined: 19 years ago

Wjohn has a email he can forward you, or i can, or anyone else who has it. That lists all the prices, and links to how to build them, and possibly links to parts.


Reply
Page 1 / 4
Share: