GECE Controllers
 
Notifications
Clear all

GECE Controllers

23 Posts
6 Users
0 Reactions
5,032 Views
sporadic
Posts: 1199
(@sporadic)
Noble Member
Joined: 14 years ago
Christopherrto wrote:So I got my ESPixel Sticks, installed software, got them online, got one connected to a GECE string, but I can't get them to work. Most of the lights light up white, a few random colours, but none update. If I restart or unplug and plug back in the string/esp they turn on slightly different. Any ideas what I'm doing wrong? I'm using g-28 24 LED 5 wire lights I bought from Costco last season.

5 wire lights? Not familiar with those, I've only see GECE 3 wire. Can you send a picture of them and how they connect to the oem control gox?

Also, in regards to the amazon.ca link above, that's not me. That's someone else buying my controllers and re-selling them. Not sure who it is yet.


Reply
Posts: 10
Topic starter
(@christopherrto)
Active Member
Joined: 6 years ago
sporadic wrote:5 wire lights? Not familiar with those, I've only see GECE 3 wire. Can you send a picture of them and how they connect to the oem control gox?

Also, in regards to the amazon.ca link above, that's not me. That's someone else buying my controllers and re-selling them. Not sure who it is yet.

I purchased mine from Forkineye.com

Here is a picture when I cracked it open. It's 3 wire to the pixels, plus 2 wire AC power (for end plug). I cut the module into the 3 wire, connecting the transformer side to V in, led side to V out, center wire to D+. I've tried both 3.2 and 4.0b3, 4.0b3 doesn't want to light them at all, though 1 led will light each time I reset it. 3.2 lights most of them, most white, a couple vibrant colours. So it seems the controller can control them but there's something wrong.

20211002 155443 x1280

Reply
Posts: 10
Topic starter
(@christopherrto)
Active Member
Joined: 6 years ago

Here's a picture hooked up and of the box

20211002 181430 1280x
20211002 181328 1280x

Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
sporadic wrote:5 wire lights? Not familiar with those, I've only see GECE 3 wire. Can you send a picture of them and how they connect to the oem control gox?

Also, in regards to the amazon.ca link above, that's not me. That's someone else buying my controllers and re-selling them. Not sure who it is yet.

This is the seller . I did not realize this wasn't your account . Had I known it wasn't you I would never have posted it .

Deleting that fraudster link now .


Reply
sporadic
Posts: 1199
(@sporadic)
Noble Member
Joined: 14 years ago

Can you get a voltage reading coming out of that box? Most people I know just ditch the oem box and use a 5V supply. I'll test 4.0-beta3 on gece tomorrow. 3.2 should be working though. I think it's that oem power brick.


Reply
Posts: 10
Topic starter
(@christopherrto)
Active Member
Joined: 6 years ago
sporadic wrote:Can you get a voltage reading coming out of that box? Most people I know just ditch the oem box and use a 5V supply. I'll test 4.0-beta3 on gece tomorrow. 3.2 should be working though. I think it's that oem power brick.

Brick says 5.5V, 11W (so 2A)
No load voltage measures 5.36V
That should be plenty of juice, shouldn't it?

I would think if it was a power supply issue the lights would update but dim/flicker/discolor.


Reply
sporadic
Posts: 1199
(@sporadic)
Noble Member
Joined: 14 years ago
Christopherrto wrote:Brick says 5.5V, 11W (so 2A)
No load voltage measures 5.36V
That should be plenty of juice, shouldn't it?

I would think if it was a power supply issue the lights would update but dim/flicker/discolor.

Yeah, that should be good. Is the larger gauge wire just a pass through extension cord? The ones I have are older models with just 3 wires. I'll do some research and see if something has changed with the protocol. The do have it be assigned addresses each time they're powered up which the firmware takes care of. So if you're seeing some lights responding correctly and others not, it would be an addressing issue. Sounds like something else going on though.


Reply
sporadic
Posts: 1199
(@sporadic)
Noble Member
Joined: 14 years ago

I just verified 4.0-beta3 working on my GECE test setup. Make sure you power cycle after configuring the output for GECE so the controller can properly initialize the lights. I'll continue to look into any protocol updates.


Reply
Posts: 10
Topic starter
(@christopherrto)
Active Member
Joined: 6 years ago
sporadic wrote:I just verified 4.0-beta3 working on my GECE test setup. Make sure you power cycle after configuring the output for GECE so the controller can properly initialize the lights. I'll continue to look into any protocol updates.

I took a video to help see what I'm doing. Sorry for the quality/mess.

I'm guessing the new lights might be working on a slightly different protocol. I can send you a set, or I could break out my oscilliscope and take readings from the control box if those would be helpful. I'm not sure if they're going to carry them this year at Costco, but I have a dozen boxes I was hoping to setup, and know a few other people in my area who bought them and don't like the stock options.


Reply
sporadic
Posts: 1199
(@sporadic)
Noble Member
Joined: 14 years ago
Christopherrto wrote:I took a video to help see what I'm doing. Sorry for the quality/mess.

I'm guessing the new lights might be working on a slightly different protocol. I can send you a set, or I could break out my oscilliscope and take readings from the control box if those would be helpful. I'm not sure if they're going to carry them this year at Costco, but I have a dozen boxes I was hoping to setup, and know a few other people in my area who bought them and don't like the stock options.

Are you able to get on the xLights Zoom room for a bit? The link is here on the right - https://xlights.org/ If so, message me (Shelby) when you get on and we can jump in a breakout room. Will be on in about 5min til around noon est or so. If not, let me know when a good time is.


Reply
Page 2 / 3
Share: