Brief Scheme ...
 
Notifications
Clear all

Brief Scheme ...

11 Posts
3 Users
0 Reactions
4,438 Views
Posts: 87
Topic starter
(@jammerone)
Estimable Member
Joined: 17 years ago
[#11159]

What is the Passage Between PC and the Controller ?

Serial to RJ45

Any item Between PC and Renard Controller

Regards,


10 Replies
Posts: 502
(@mmulvenna)
Honorable Member
Joined: 19 years ago
Jammerone wrote:What is the Passage Between PC and the Controller ?

Serial to RJ45

Any item Between PC and Renard Controller

Regards,

I use usb to rs485....:)


Reply
Posts: 87
Topic starter
(@jammerone)
Estimable Member
Joined: 17 years ago

so sir you mean this

then according to the Diagram

What I connect to the CAT5?

Thanks for the Reply ..

Best REgards,


Reply
Posts: 502
(@mmulvenna)
Honorable Member
Joined: 19 years ago
Jammerone wrote:so sir you mean this



then according to the Diagram

What I connect to the CAT5?

Thanks for the Reply ..

Best REgards,

This is like the ones I use. It hooks to a USB port on your computer. Then you cut the cat 5 connector off one end and hook the appropriate wires to the + and - on this board and the other end to the rj45 input on the renard controller.


Reply
Posts: 87
Topic starter
(@jammerone)
Estimable Member
Joined: 17 years ago

No Assigned Color on CAT 5 ...?

like

" + = white orange " and " - = Orange "
" + = white green " and " - = green "

I crimp my RJ45 in normal way like network color assigning

Thanks ... I already start in Renard / Arch but this will be the remaining question in my mind ..

your answer is very appreciated sir ...

Best Regards


Reply
Posts: 502
(@mmulvenna)
Honorable Member
Joined: 19 years ago
Jammerone wrote:No Assigned Color on CAT 5 ...?

like

" + = white orange " and " - = Orange "
" + = white green " and " - = green "

I crimp my RJ45 in normal way like network color assigning

Thanks ... I already start in Renard / Arch but this will be the remaining question in my mind ..

your answer is very appreciated sir ...

Best Regards

Yes standard network wiring(crimping) applies. My cables are hooked up to the adapter like this for renard but opposite for other controllers.

Solid Blue........ to the adapter "-"
Striped Blue..... to the adapter "+"


Reply
Posts: 87
Topic starter
(@jammerone)
Estimable Member
Joined: 17 years ago

@mmulvenna

Thank you very much .. very well infotmative for me and to other newbie ..

I will order USB to RS485 and Apply that ...

What about the ground?

by the way what you mean opposites to another controllers?

Thanks ..

Best REgards,


Reply
Posts: 502
(@mmulvenna)
Honorable Member
Joined: 19 years ago
Jammerone wrote:@mmulvenna

Thank you very much .. very well infotmative for me and to other newbie ..

I will order USB to RS485 and Apply that ...

What about the ground?

by the way what you mean opposites to another controllers?

Thanks ..

Best REgards,

Animated Light for example would have the Blue and blue-white just the opposite of these.

Only use the 2 wires for your renard controllers. Just "+" and "-"


Reply
Posts: 859
(@smartalec)
Prominent Member
Joined: 17 years ago
mmulvenna wrote:Yes standard network wiring(crimping) applies. My cables are hooked up to the adapter like this for renard but opposite for other controllers.

Solid Blue........ to the adapter "-"
Striped Blue..... to the adapter "+"

For Gnd i used brown & brown striped.
blue goes to 'B'
blue/striped goes to 'A'

worked for me


Reply
Posts: 87
Topic starter
(@jammerone)
Estimable Member
Joined: 17 years ago
smartalec wrote:For Gnd i used brown & brown striped.
blue goes to 'B'
blue/striped goes to 'A'

worked for me

You mean "B" and "A" is different Controller.

I am right?

Best REgards,


Reply
Page 1 / 2
Share: