Xbee to esp testing...
 
Notifications
Clear all

Xbee to esp testing question

27 Posts
6 Users
1 Reactions
1,687 Views
Posts: 168
Topic starter
(@jvalue)
Estimable Member
Joined: 16 years ago
[#59064]

Hi,
Should I be able to test the lights on my ss24 using the esps controller admin page (diagnostics) or do I need to go through my pi with a sequence? Thanks for your time..
Jim


26 Replies
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

You would use the effects available on the device page under secondary input. You would set the output to Renard.


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago
jValue wrote:
my ss24 using the esps controller admin page

If you're talking about the ESPixelstick software on an ESP type microcontroller, then sorta. The ESPixelstick software was originally meant to control pixels, which is three channels. So, the test modes are per three channels too, but it does all pixels at the same time. It doesn't have a test that walks through one (Renard) channel at a times. It'll show you three channels at a time, as though it was a pixel. You can do the single channel walk through with your sequencing software.


Reply
Posts: 168
Topic starter
(@jvalue)
Estimable Member
Joined: 16 years ago

Thanks, I'll try these two suggestions. It's looking like I may have chosen the wrong jumper option on the snap-in.


Reply
Posts: 397
(@billw)
Honorable Member
Joined: 16 years ago

Since you know the SSID and IP address, you can test it using the Vixen 3 web server. That’s how I handle mine after reprogramming the PIC and installing the ESP on my boards.


Reply
Posts: 168
Topic starter
(@jvalue)
Estimable Member
Joined: 16 years ago

Vixen 3 Web server!?! I'll take a look! Thanks for the tip


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Since you have an SS24 and 24 channels is divisible by 3, you'll be okay. If you had an SS8 instead, you would need to set the ESP's "number of channels" to 9 instead of 8 because, as Ernie mentioned, it "thinks" in groups of 3 and to send a complete packet out, you need a completed group of 3 pixels. If you have an SS16 controlled by ESPixelStick firmware, you'd need to set it to 18 channels instead of 16 for the same reason. Obviously, this affects downstream controllers if you're daisychaining off the Renard to another Renard.


Reply
Posts: 397
(@billw)
Honorable Member
Joined: 16 years ago
dirknerkle wrote:
Since you have an SS24 and 24 channels is divisible by 3, you'll be okay. If you had an SS8 instead, you would need to set the ESP's "number of channels" to 9 instead of 8 because, as Ernie mentioned, it "thinks" in groups of 3 and to send a complete packet out, you need a completed group of 3 pixels. If you have an SS16 controlled by ESPixelStick firmware, you'd need to set it to 18 channels instead of 16 for the same reason. Obviously, this affects downstream controllers if you're daisychaining off the Renard to another Renard.

I tried that but only managed to get every third channel to turn on, so I must have done something wrong. I’ll take another look at it later.

jValue wrote:
Vixen 3 Web server!?! I'll take a look! Thanks for the tip

Once your PC and controller are on the same network, using the web server is simple. Go to Tools > Web Server, and when the configuration window appears, click the link. A new window will open with all your elements—just select the one you want to test and follow the prompts.

Web server

Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
dirknerkle wrote:
Since you have an SS24 and 24 channels is divisible by 3, you'll be okay. If you had an SS8 instead, you would need to set the ESP's "number of channels" to 9 instead of 8 because, as Ernie mentioned, it "thinks" in groups of 3 and to send a complete packet out, you need a completed group of 3 pixels. If you have an SS16 controlled by ESPixelStick firmware, you'd need to set it to 18 channels instead of 16 for the same reason. Obviously, this affects downstream controllers if you're daisychaining off the Renard to another Renard.

The latest build from earlier this week fixed that issue.


Reply
Posts: 397
(@billw)
Honorable Member
Joined: 16 years ago
MartinMueller2003 wrote:
The latest build from earlier this week fixed that issue.

Which build are we referring to? I’m using ESPixelstick firmware 3.2, and if this isn’t the latest version, it might explain some of the issues I’ve been experiencing. Do you have an updated version and link?


Reply
Page 1 / 3
Share: