I bought a WF300 wifi pixel controller to try out and play with. I wired it up to 12v power plugged in a 2811 pixel sting of course 12v. Grabbed my phone turned on wifi. It found it and connected. I opeed the app and connected to controller. As soon as I told the app what type of controller it dropped wifi and my phone can not find nor see the signal. The Led on the controller says its working.
And the RF remote still works controlling lights.
Anyone know anything about these. Maybe how to reset wifi.
Complete instruction set >
you probably switched it to rf mode
Also how big is this 12v supply? I dont specifically in this case but brown out is a possibility too.
why would the power supply matter, it can handel up to 24v. I know its not a power supply issue. also there is no switch it does RF and Wifi at the same time, plus there is no switch.
If you look at the documentation on the link i posted there is several modes wifi _ rf etc.
Scroll down the page and look at example 3. it explains in detail about drop out and to enter run to setup your wifi
1. LED-WiFi Controller
It is the core of product, responsible for receive control signal and control LED equipment.
2. RF remote control
In the condition of not use the mobile phone as remote control, you can choose RF remote control to control LED
LED-WiFi Controller Function Instruction
1. Working state instruction
Indicator light
Function table
Power
Power indicator light, long-time bright shows power supply normally
Wifi
Free time long-time bright, have wifi data enter flicker, configuration wifi Ssid off
Link
Have wifi date enter, then flicker, no wifi data, then off.
RF
Have RF remote data or press key operate, then flicker, free time off.
2. Setting SSID number
The dial code is used for setting LED-WiFi controller Ssid number, corresponding table as below. Form 0 to 15, have 16 code in total, so our Ssid number fasten to LN001 to LN016. That means use our product in same small area can set 16 mutual isolation LAN, once the dial code changed after switch was dialed, Ssid number immediately be modified, so you need to note that it need to search and connect again.
code
SSID
0
LN001
1
LN002
2
LN003
3
LN004
4
LN005
5
LN006
6
LN007
7
LN008
8
LN009
9
LN010
A
LN011
B
LN012
C
LN013
D
LN014
E
LN015
F
LN016
3. Connect LED, Power supply port
LED Strip according model connect corresponding port.
4. Match Key function
The first time use the controller and remote control, maybe because the controller address and remote control address is not match, it will cause the remote control can not control, at this time, it need to use this button to make this 2 address matched.
Use method: first, press the controller "Match" key, at the same time press any key of the remote control, more than 2s, now the remote control indicator light RF will flicker 3 times, release "Match" key, then finished.
5. Function key function
“Function” key is a composite button, it have switch and mode change function.
Function instruction: long-time(more than 2s): on off;
Short press(less than 1s): mode change.
1. Controller panel have 64 touch point, and the function as follow:
1. ON/OFF,you can turn on/off controller output at any time;
2. Pause,at dynamic mode, you can stop the controller at the current state;
3. This button have 2 functions :
Mode + choice key, when current control pattern is pulley pattern (color), if must
realize the pattern (color)in the controller, can press this key.
mode switch button, for the current control mode, you can switch M + key which
is specified mode (color) in the table.
4. This button have 2 functions :
Mode - choice key,when current control pattern is pulley pattern (color), if must
realize the pattern (color)in the controller, can press this key.
mode switch button,For the current control mode, you can switch M + key which
is specified mode (color) in the table.
5. The output brightness control key,every time you press this button, the brightness series
add 1,altogether 32 levels.
6. The output brightness control key,every time you press this button, the brightness series
minus 1, altogether 32 levels.
7. The output speed control key,every time you press this button, the brightness series
add 1, altogether 99 levels.
8. The output speed control key,every time you press this button, the brightness series
minus 1, altogether 99 levels.
9. Color pulley touch button, static mode choose button, up to 55 touch points.
this button have 2 functions:
