Strange Pixel issue
 
Notifications
Clear all

Strange Pixel issue

8 Posts
4 Users
0 Reactions
1,129 Views
Posts: 133
Topic starter
(@byhova)
Estimable Member
Joined: 9 years ago
[#58406]

Wanted to see what some thoughts about this strange issue. I have 2 sets of 68 pixels (each window is 68) the first window is working. When I jump to the second window all the pixels flash white no matter what color it is on sometimes very fast so I thought it was a data issue but the distance on the house is less than 10' apart. So, I brought the window pixel outlines in the house and hooked it up by itself and it will display the color but will flash white randomly not every time but just sometimes doing just white, red, blue, green, then off, color pattern. It may flash white when doing say the red pattern then it may not do it again for 2-3 minutes or it will do it 2-3 times in one cycle. I am doing all this testing in my room; the controller and wire is less than 3 ft. away from each other so no need for a null pixel. No matter what I hook up after the 2nd window (the 68pixels) it makes everything flash just like them. If i put anything before the 2nd window they flash also. So, I grabbed a brand-new strand of 50 and ran just 50 from the controller the same thing. if I put an F-amp right in front of the new 50-pixel strand, the 50 work just like they should. If I take the F-amp out they flash & so do the lights after it. Same thing with the window if I put the F-amp right in front of it so 18" to F-amp to 6" first pixel it won't flash.??? But, the first window of 68 work just like they should with no issue. The only way I can get the first window to flash is if I put them After the 2nd window but if they are first (like they are on the house they work fine) but the 2nd window still flashes even with an F-amp between them.

It's odd that this new strand of 50 & the window of 68 ONLY do not flash if I put an F-amp before the strand hooked directly to the controller. Like I said though it is less than 3 feet from the controller. All the lights are from DIYLEDEXPRESS these were not the bad batch of pixels this is what the rest of my house is running with no issue. I ordered the entire set of lights all at the same time, so they all came together. Any help is much appreciated.

I am using a F16v3 for my controller if that matters for my show but using an ESPArtStick for testing but am getting the same results with both controllers. It is just warming doing to the testing inside


7 Replies
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

What is your pi point? What is the v+ at the last working pixel. do you have data and v- from last pixrl in window 1 to first pixel in window 2?


Reply
Posts: 133
Topic starter
(@byhova)
Estimable Member
Joined: 9 years ago
MartinMueller2003 wrote:
What is your pi point? What is the v+ at the last working pixel. do you have data and v- from last pixrl in window 1 to first pixel in window 2?

Reply
Posts: 133
Topic starter
(@byhova)
Estimable Member
Joined: 9 years ago
MartinMueller2003 wrote:
What is your pi point? What is the v+ at the last working pixel. do you have data and v- from last pixrl in window 1 to first pixel in window 2?

Not sure what you mean by pi point sorry about that...My controller is less than 15' away from the starting point of the first window on my outside setup. For my set up I am power injecting in between window 1 & 2. There is no back feeding into either power supply

This is for the current testing I am doing; I have the brightness at 50% on the controller and had the color wash brightness set to 70% just so I didn't have to power inject inside my house while doing the testing. But after my first window of 68 pixels I have 11.90V on the V+ side. after 136 pixels not power injecting just in the house but I am getting 10.9V (all white) but any other color is 11.3-11.4V.

I have a common ground


Reply
rstehle
Posts: 4348
(@rstehle)
Illustrious Member
Joined: 19 years ago

Are you by chance feeding data again at your injection point? (you shouldn't).


Reply
Page 1 / 2
Share: