https://www.techradar.com/news/good-luck-getting-hold-of-the-latest-raspberry-pi-any-time-soon
IMO the Christmas ecosystem needs to move to Falcon and BBB.
Unless you need to run a Pi chapeau I would think an Orange PI 3 LTS should work. The manufacturer has a store on Aliexpress: https://www.aliexpress.com/store/1100997172?spm=a2g0o.detail.1000007.1.35f03185hcgeLZ They are less expensive and available. I have to admit I have not tried one but plan to order one at some point.
How's the FPP6 GPU stuff work on the knockoffs? If it only supports 2 channels or you have to pay licensing, the BBB may not be that much more expensive. What I don't like is that there's a greater community of stuff for Raspbian Pi than there is for Ubuntu BBB. Although it does not do a lot of good to have all this software available for hardware you can't have.
pixelated wrote:Unless you need to run a Pi chapeau I would think an Orange PI 3 LTS should work. The manufacturer has a store on Aliexpress: https://www.aliexpress.com/store/1100997172?spm=a2g0o.detail.1000007.1.35f03185hcgeLZ They are less expensive and available. I have to admit I have not tried one but plan to order one at some point.
Just an fyi, I tried an OrangePi 3 LTS and had trouble with the Wifi once FPP was installed. I think if were to try it again using OrangePi's builds instead of Armbian it may have worked but I have since swapped it out with my Octoprint Raspberry Pi.
ctmal wrote:Just an fyi, I tried an OrangePi 3 LTS and had trouble with the Wifi once FPP was installed. I think if were to try it again using OrangePi's builds instead of Armbian it may have worked but I have since swapped it out with my Octoprint Raspberry Pi.
Chris,
So you are saying that the OrangePi is working to run Octoprint? Great, that will allow me to free up a RPi.
TomL8345 wrote:Chris,So you are saying that the OrangePi is working to run Octoprint? Great, that will allow me to free up a RPi.
Well, yes and no. I stopped using it for FPP because I had issues with WIFI once FPP was installed. After the 1st reboot wifi would disappear. When i used a wired connection everything seemed to work fine.
After playing with for awhile I decided to replace my Octoprint server which was a RPi 3 b+ with the OrangePi. I did run into more wireless issues with that until I used the OrangePi debian package. Since then I haven't had any issues.
Knowing what I know now, I would bet that if you started with the OrangePi debian package and installed FPP overtop that, wireless would continue working. I can't test that now though since its being used for Octoprint now.
Also, the OrangePi 3 LTS runs very hot! In open air I was seeing temperatures of 50 - 70 degrees C. I connected a 5V fan that I ripped out of an old laptop and now I'm staying under 40 degrees consistently. Right now I have it running at all times but one of these days I'll probably write a script to only turn it on when hot. Although it might just end up running all the time anyway.
TomL8345 wrote:Chris,So you are saying that the OrangePi is working to run Octoprint? Great, that will allow me to free up a RPi.
Ha, just realized I misread your post. Yes, it's working great for OctoPrint. Definately need the fan though.
The shortage may be coming to a close for 2023! May have new Pi 5's out with an improved graphics card. The wheels in my head are turning what I would do already.
I use one Pi in my show, and that is just to send out a Serial signal to my old High Voltage Box powered with an Arduino. I use a laptop to run the show.

