Panel Mount Waterpr...
 
Notifications
Clear all

Panel Mount Waterproof Connectors

11 Posts
6 Users
0 Reactions
4,632 Views
shanicus
Posts: 266
Topic starter
(@shanicus)
Reputable Member
Joined: 14 years ago
[#30015]

I've searched around here and on the Wiki but cannot find mention of a panel mount style connector. Does anyone use panel mounts instead of just the "tails" for their pixel connections? If so, where do you buy them from?

I'm currently using the 3 pin connectors from DIYLEDexpress and while they work fine I'm after a cleaner look and an easier way to connect and disconnect outboard equipment.

I have found a few sources on the internet but I am unsure of the sizing, pin spacing, keying and threading of my existing connectors to blindly order something that may or may not work - well I might do that anyway but I figured I'd check with the experts here first!

Thanks,

Shane


10 Replies
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

I think I saw one in a data sheets Ray sent me a while back. I think they were for the 13.5 mm connectors but I need to check with Ray.


Reply
Posts: 2229
(@plasmadrive)
Famed Member
Joined: 15 years ago

I have a lot of chassis mount Devicenet connectors. They are four pin. Two power and two data. when used with the right male connector they are water tight.

The look like this
http://www.directindustry.com/prod/dongguan-finecables-co-ltd/circular-connectors-cordsets-sensors-70478-661275.html


Reply
Electrified3
Posts: 716
(@electrified3)
Prominent Member
Joined: 13 years ago

Coming from Industrial controls I can say there are all kinds of products on the market for panel mount quick connectors. A common one I have used is Brad Harrison, but also Pheonix Contact makes them and several other manufacturers. These will have "pigtails" that can be mounted right to your enclosures and they make cordsets of various lengths and pin configurations for field connections. Then there is Amphenol, they make connectors for everything but most you need to assemble, solder, crimp pins and so forth.

Here is the kicker, it is cost. The quick connectors available through Ray Wu, DiyLED, etc are VERY CHEAP compared to what these other products will cost you. All a matter of what you want to spend at the end of the day.

Here is a link to Brad Harrison, most likely Mini or micro cordsets and pigtails would be what you are looking for.
http://www.bradharrisonsales.com/mic_3-5p_pvc_skm12_dc.htm

Here is a link to Amphenol on Mouser,
http://ca.mouser.com/Amphenol/?gclid=CIzW1_Tk87sCFYlAMgodlX4AjQ


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

For those in the US here is the Amphenol link on Mouser.

I for one would love to use DeviceNet for Power over DMX application as the cable specifications are a perfect fit. However the cost of the connectors is quite high. It would be reasonable to consider the lower cost 5 pin 15mm connectors Ray can get with DeviceNet cable if the cable could be found in China at a reasonable price.

I like the Brad Harrison cable sets however they are only rated at 4A. That's not enough when connecting multiple strings together unless you can run 24 or more volts down the string and use local switching regulators. It's something that would be interesting and I've been looking into it but right now it's just an idea.


Reply
Electrified3
Posts: 716
(@electrified3)
Prominent Member
Joined: 13 years ago

The Brad Harrison cable sets come in many formats, I am thinking the 4 amp rated ones are micro or nano using 22awg wire which is cause for the limitation. Various other sets use different gauge wiring, I have used some up to #8awg. There are many types available.

Another option to look at are the end connectors, they are thread together modular ends, waterproof and even have screw terminals in them instead of having to solder or crimp, handy for re-using them as well or replacing bad cables.

Another thought are the Phoenix distribution blocks, these take a "trunk" cable from the source controller to the field area then have break outs to plug in multiple devices using all quick connects. Again though, cost prohibitive, can buy another controller for the cost of the block and cables!! http://ca.mouser.com/ProductDetail/Phoenix-Contact/1692459/?qs=sGAEpiMZZMsYTROW9%2fpt5A81dYw9434S3FuwOFj45CI%3d

Might have to try these and see how it works out, I have about 4 or 5 of them left over from a project I did 10 years ago.


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

I use XLR connectors. I'm in the audio industry so they're plentiful to me. I use the name brand neutrik ones with the gold plated contacts. (NC3FX-B, NC3MX-B, etc...) they're not specifically waterproof, but no less waterproof than a vampire plug or anything else we commonly use. But I always use dielectric grease on all of my connections anyhow. I've had zero problems related to connections.


Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

Neutrik makes some damn nice connectors and they have quite a few that are water resistance.


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

they sure do. but they're expensive. and sometimes their less common part numbers are hard to find in stock anywhere.


Reply
shanicus
Posts: 266
Topic starter
(@shanicus)
Reputable Member
Joined: 14 years ago

Thanks everyone for you input. That's some food for though. I figured it was a cost factor as to why most people chose to use tails instead of panel mounts but in reading through all of your reply's and checking out the product links posted, another thought occurred to me: how about instead of using a panel mount with solder-on or pre-made tails on the opposite side, I just use an inline connector like a thru-barrel or gender changer? Sort of a do-it yourself panel-mount. Along the lines of using a "T" tap for power injection, but without the branch off. More like an inline extension connector or coupler. So on the output side, it would be appear as a panel mount and on the input side it would appear as the same. So you would still have use a tail to make the input side connection but it would achieve the same result for the output side connection point. I believe those do exist but I'm not sure if they are threaded fully on both sides to allow it to be mounted through a flat surface (like the wall of a project box or other enclosure).

Along the lines of this (but picture it as a Waterproof LED connector, not an F81 for Coax):

images

jchuchla: I did notice you used XLR's from some of your photo's in other posts and I was going to ask you about their reliability but I assumed that they were the water-proof variety. Now that you mention they are standard grade and they are working fine I may reconsider my options as I do have a bunch of panel mount XLR headers and XLR connectors laying around that I'll probably never use for anything else.

Still, I don't like mixing connector types as I'm bound to accidentally plug something in that doesn't belong and damage something in the process 🙁

Thanks again folks!

Shane


Reply
Page 1 / 2
Share: