Help me decide on a...
 
Notifications
Clear all

Help me decide on a controller

65 Posts
18 Users
0 Reactions
64.7 K Views
Posts: 344
 TSL
(@tsl)
Reputable Member
Joined: 10 years ago

No problem. If split evenly between the 48 possible ports it would be about 340 pixels per port. I use two banks on my F48 so I can run just shy of 800 pixels per port. Which is perfect for my roof, eaves, windows and door outlines.

Sent from my iPhone using Tapatalk


Reply
wilmar
Posts: 2115
(@wilmar)
Noble Member
Joined: 8 years ago
TSL wrote:No problem. If split evenly between the 48 possible ports it would be about 340 pixels per port. I use two banks on my F48 so I can run just shy of 800 pixels per port. Which is perfect for my roof, eaves, windows and door outlines.

Sent from my iPhone using Tapatalk

I’m looking into these falcons but very confusing for non experienced folk to understand as I seen this part too ... for f48 on spec sheet .

Sent from my iPhone using Tapatalk


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

The issue is that you are looking for absolute values. The Falcon product is not designed that way. The Falcon F16 and F48 can drive up to 16,000 (I rounded the number) pixels. The two variants can have up to 1024 pixels connected to any given port. However, the 48 port Falcon can still only drive a total of 16,000 pixels so you cant have 1024 pixels on every port (that would be 48,000 pixels).

The next independent reality is that the more pixels you put on a port, the longer it takes to refresh the pixels in that string. The Falcon uses a sliding refresh rate based on the number of pixels configured to be present on the port. You will get 40 FPS (25ms) when there are up to 680 pixels on the port. When you go over that limit, the controller switches to 20 FPS (50ms).

The F48 does not have ANY ports on the main board. Each connector on the main board is designed to connect to a receiver that has four output ports. Each of those ports can drive a string of pixels. If you limit the length of each string to 680 pixels, you will still exceed the 16,000 pixel limit. The practical limit on each output port on the F48 is ~341 pixels per port. NOTE: I said practical limit, some ports can have more and others would need to have less and the total must be below 16000.

Long explanation to say:

  • There is one hard limit: 16384 pixels on the controller.
  • There is a physical limit (16 or 48 ports).
  • There is a physical limit for the refresh rate based on the number of pixels connected to the port.

Reply
wilmar
Posts: 2115
(@wilmar)
Noble Member
Joined: 8 years ago
MartinMueller2003 wrote:The issue is that you are looking for absolute values. The Falcon product is not designed that way. The Falcon F16 and F48 can drive up to 16,000 (I rounded the number) pixels. The two variants can have up to 1024 pixels connected to any given port. However, the 48 port Falcon can still only drive a total of 16,000 pixels so you cant have 1024 pixels on every port (that would be 48,000 pixels).

The next independent reality is that the more pixels you put on a port, the longer it takes to refresh the pixels in that string. The Falcon uses a sliding refresh rate based on the number of pixels configured to be present on the port. You will get 40 FPS (25ms) when there are up to 680 pixels on the port. When you go over that limit, the controller switches to 20 FPS (50ms).

The F48 does not have ANY ports on the main board. Each connector on the main board is designed to connect to a receiver that has four output ports. Each of those ports can drive a string of pixels. If you limit the length of each string to 680 pixels, you will still exceed the 16,000 pixel limit. The practical limit on each output port on the F48 is ~341 pixels per port. NOTE: I said practical limit, some ports can have more and others would need to have less and the total must be below 16000.

Long explanation to say:

  • There is one hard limit: 16384 pixels on the controller.
  • There is a physical limit (16 or 48 ports).
  • There is a physical limit for the refresh rate based on the number of pixels connected to the port.

Why couldn’t they just put that in the manual lol ... thanks

Sent from my iPhone using Tapatalk


Reply
Posts: 344
 TSL
(@tsl)
Reputable Member
Joined: 10 years ago
wilmar wrote:Why couldn’t they just put that in the manual lol ... thanks

Sent from my iPhone using Tapatalk

It really comes down to your layout and if the F48 is the correct controller or would a F16 with an expansion board or two do the trick for you. Either way you can’t go wrong with a Falcon product. I have a F48 and a F16 with an expansion boar. Both work great for me.

Sent from my iPhone using Tapatalk


Reply
Page 5 / 13
Share: