Experience Wanted
 
Notifications
Clear all

Experience Wanted

22 Posts
8 Users
0 Reactions
4,236 Views
Posts: 3735
Topic starter
(@algerdes)
Famed Member
Joined: 15 years ago
[#55827]

For many years now, we have used pixels, pixel controllers, and players. Our players have changed from full blown computers (desktop and laptop) to credit card computers (Raspberry Pi, Beagle Bones, etc.), the main part of the display has several (player/remote). The controllers have been subjected to power being turned on and off, but the players have always been on full time (always on) circuits. We do have one set of props that the controller is a RPi with a Falcon Pi Hat. This unit is subjected to the nightly power on/off cycle. We set the sequence times for this unit at 00:01 till 23:59 and load an onboard RASclock so that when power comes on, it automatically starts its sequence. When the power goes off, well - it shuts off.

I say all of this as we are now going to add 3 larger matrices that will be in an area that does not have full time power. They will be subjected to power on (usually 30 minutes before opening) and power off (usually 15 minutes after closing) along with the occasional "bounce" during opening or close. (People who can't handle the large breaker sometimes slip and it comes right back on.) In the early days there was the possibility of corrupting data cards, but to be honest we never experienced it with the PiHat on the RPi.

I've purchased 3 Kulp K8-B controllers (one for each stand-a-lone matrix) and am building enclosures and the matrix panels themselves. I am very concerned as to the K8-B and how it handles power on/power off cycles. ANY information would be helpful. In particular, I am looking for input if anyone else is using their K8-B in a power on/power off scenario and if there are any problems associated with this setup.

Thanks in advance.

Al


21 Replies
dirknerkle
Posts: 10308
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Al, what does Dan say about it?


Reply
Posts: 128
(@sctwohig)
Estimable Member
Joined: 10 years ago

I am not sure if this answers your question or not, but I started powering of all my remotes in 2021. I used fpp 5.2 master/remote. I am using Smart plugs and home assistant to control the power to the remotes. I have a pi setup as my master and it remains powered on 24x7, and various other pis/ beaglebones setup as remotes. I also have a mqtt broker configured in fpp so fpp can interact with home assistant. I ended up adding a script in my playlist leadout "ShutdownRemotes.sh" You need to supply the IP's of the remotes in the script and include the shutdown.sh script to each of the remotes. So all my remotes shutdown after my leadout song finishes. Then my playlist has a 60 second pause, and the my playlist leadout I run a command that has a mqtt to power off my smart plugs. So with this setup my remotes shutdown then home assistant powers them off, all controlled by fpp. If my show runs late nothing shuts down. The next day I have a playlist that runs 10 minutes before my main playlist runs that sends the mqtt commands to turn on my smart switches, which turns on my controllers once they get powered on. I also included the mqtt commands the scheduled playlist leadin just as a precaution in case one of the smart switches failed to turn on with the 1st command. The only issue I ran into was I had 1 smart switch that would for some reason lose internet connectivity and needed to be reset a couple of times.I had 0 issues with any remotes getting corrupt or having any other issues. Because of my setup I was able to schedule my playlist to start/end at different times on different days with no issues.

Thanks,
Shawn


Reply
Posts: 3735
Topic starter
(@algerdes)
Famed Member
Joined: 15 years ago

Thanks sctwohig.
Your statement, "I have a pi setup as my master and it remains powered on 24x7" lies right in line with what we usually do. Though we may take controllers down, the player stays powered.
In the case of our new props, this will be impossible. Power for the whole side of the park is manually shut down each evening and then turned back on the next day just before we open the gates.


Reply
Posts: 3735
Topic starter
(@algerdes)
Famed Member
Joined: 15 years ago

Dave,
Just heard from Dan on one of the other sites. He is shutting down everything in his show, except his master. There in lies the difference between what I have to do (environment wise). My player ("master" if you will) does not have full time power for the units. Oh well. I'm trying to get the first of the units finished within the week. Once it is ready, I'll hook it up to a timed power switch and let it cycle the power on and off (with appropriate lengths of time between each cycle) to see what happens.

I was just hoping someone else already had experience with this "situation".


Reply
Page 1 / 5
Share: