ESPixelStick Flash ...
 
Notifications
Clear all

ESPixelStick Flash Tool

223 Posts
49 Users
0 Reactions
100.3 K Views
Posts: 793
(@covewi)
Noble Member
Joined: 17 years ago

I purchased 3 ESPixelsStick (Forkineye) modules on Amazon ( by the way - very good service) and the USB to Serial breakout board suggested from Forkineye's
website - http://forkineye.com/espixelstick/ .
Followed the instructions and double checked the connections, applied a 12V PS to the ESP, plugged the serial adapter into my MAC. The Arduino software still thinks an Arduino MEGA is attached.
I started a thread here - http://doityourselfchristmas.com/forums/showthread.php?50007-What-Do-I-Need - but saw this thread and jumped on.

ESP

Screen Shot 2017 12 30 at 9.56.36 AM

Screen Shot 2017 12 30 at 9.56.52 AM

This shows up under the Arduino Tools tab - does that mean theres a serial port available?

Screen Shot 2017 12 30 at 10.01.03 AM

Hooked up the Arduino Mega and the USB port shows up

Screen Shot 2017 12 30 at 10.20.43 AM

Thanks


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

YOU have to configure the Arduino IDE to tell the IDE what you have connected. The Arduino IDE does not auto detect the device at the end of the serial adapter.


Reply
jrock64
Posts: 1099
(@jrock64)
Noble Member
Joined: 19 years ago

I purchased one of the CH340G based programmers a while back for less than $3
https://www.ebay.com/itm/OPEN-SMART-USB-to-ESP8266-ESP-01-Wi-Fi-Adapter-Module-w-CH340G-Driver-Hot/152700861994?hash=item238dae3e2a:g:I-sAAOSwaIRZt6im

I was not expecting much, but I was willing to try it anyway.

Plugged in an ESP set it to program and plugged it into a USB socket.

The software recognized the CH340G so I told it to program.

The screen told me it was successful.
And also what IP address had been assigned so I could immediately connect to it and reconfigure to my settings.

Simple and SWEET
Great job.


Reply
Posts: 793
(@covewi)
Noble Member
Joined: 17 years ago

I tried the ESPS Flashtool to program the Pixelstick as Sporadic suggested . The usb - serial port does not show up. But from an earlier post you can see the USB to Uart does show up under MAC's system check. I am assuming thats the USB to serial adapter plugged into my MacBook.

Screen Shot 2017 12 30 at 8.25.36 PM

Sporadic has offered some help but not being a MAC guy I think we are both lost. Does anyone have any idea why the serial port isnt available and why the Flash tool or Arduino software doesnt see the PixelStick?


Reply
Posts: 793
(@covewi)
Noble Member
Joined: 17 years ago

Well it took 14 hours to get this to work and actual Google research. Being a MAC guy everything is different and not very straight forward. I finally went to the Silicon Laboratories website and searched their FAQ's and found USB to UART Controller drivers - https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers . Installed them and WOW. The

Screen Shot 2017 12 30 at 11.54.57 PM

showed up and presto

Screen Shot 2017 12 30 at 11.56.21 PM

.

Now for the fun stuff.


Reply
Posts: 3
(@rockendoublez)
New Member
Joined: 9 years ago

I'm having one hell of a time trying to upgrade the firmware and set the wifi using the espixel firmware tool (espixelstick from forkineye on amazon).
I'm not sure what i'm missing.
I've tried both 5v and 12v psu. putting into program mode. still won't update/connect.
drivers in windows 10 show installed properly for cp210x on com3.
i can putty to it on com3, but all i see is gibberish. same in the serial output window
r
-= Programming ESP8266 =-
bin/win/esptool.exe -cd none -cb 115200 -cp COM3 -ca 0x000000 -cf firmware/pixel-travis.bin -ca 0xDB000 -cf firmware/spiffs.bin
warning: espcomm_sync failed
error: espcomm_open failed
error: espcomm_upload_mem failed

PROGRAMMING FAILED

WhatsApp Image 2018 11 12 at 3.42.33 PM

2018 11 12 16 00 07 ESPixelStick Flash Tool

Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

did you try flipping the RX & TX on the ESPixelStick


Reply
Posts: 7
(@mdnooyer)
Active Member
Joined: 9 years ago

Hi,

Buy this one it will coast not much but it works very nice.

s l1000

Put the ESP8266 on it, in to your USB and program.
Click hier for a link to amazone.

greetz, Mark


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago
mdnooyer wrote:Hi,

Buy this one it will coast not much but it works very nice.

Put the ESP8266 on it, in to your USB and program.
Click hier for a link to amazone.

greetz, Mark

Does not have a PROGRAM button - will update, but will not work with flash tool


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Correct!

You need two boards to program an esp-01.
First you need a USB to serial converter.
The two most popular models are known as the FT232RL and CP2102.
The FT232RL by FTDI was the defacto-standard until they released a code version that would brick peoples PC's in an effort to combat Chinese clones.
This angered a lot of the Maker community. The CP2102 then arose as a competitor to FTDI.
Both of these programmers are available all over the internet, ebay and aliexpress.
You can often find them for under $2.

Secondly, you need a board to hook the FT232RL/CP2102 into,
This board has to have some small amount of circuitry on it that contains a reset button at a minimum.
Shelby's ESPixel Stick and the Pixel Pops boards have this functionality.
The Pixel Pops TINY does not.

So, if you are running pixel pop tiny's OR you want the ability to bulk program your ESP-01's you need a second board.
Dirknerkle has his Flashamater (at least until his store is closed) and I have the Pops-O-Matic boards available.
Find more detail here at this wiki:
http://www.doityourselfchristmas.com/wiki/index.php?title=Pops-O-Matic_ESP_Programmer

mrGrumpy wrote:Does not have a PROGRAM button - will update, but will not work with flash tool

Reply
Page 21 / 23
Share: