Data feed to pixels
 
Notifications
Clear all

Data feed to pixels

4 Posts
3 Users
1 Reactions
1,127 Views
Posts: 97
Topic starter
(@irrumater)
Estimable Member
Joined: 13 years ago
[#58689]

I am working through purchases and planning for my first year using pixels. I just ordered 3000 pixels and have a Kulp K8-pi setup to run them. Now it is time to seriously plan my power and cable routes.
My current plan is to mount the main controller and PS boxes on the garage wall and run cable out of there. That is within 20-25 feet of almost all the places I plan to have individual pixel props/items. I do have 2 of the LR1 Smart receivers I will place mid yard for some items out there.
My current dilemma is how best to connect to and supply power/data to the pixels on my gutter line. I plan to run 3 sides of the house with approx 750 pixels from back corner around the front and then to the back corner on the other side.
The "Beginning" of the run would be about 50-60 feet from the controller box location. So I could do 1 of 3 things I can think of :
1. Run cable to the end of the run on the back corner of the house to feed the entire 750 pixel string from 1 channel. I estimate this to be 50-60 feet from the controller, which I have read may cause an issue with data loss.
2. Is it possible to "Tee" in and feed both data and power in both directions between 2 100ct Strands? This would allow me to be only 5-10 feet from the controller depending on exactly where the junction of 2 strands ends up in the run
3. I could try to consolidate 2 other planned channels and run the gutter line on 2 separate channels one going left to the back and one going right across the rest of the front and to the end, allowing me to connect to both near the controller location.

Thoughts on the best option as well as any other advice is greatly appreciated.

TIA
Dan


3 Replies
MartinMueller2003
Posts: 7612
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Pixels take data from only one direction and there is no option to "tee". With that many pixels, you are going to need to do power injection. The details of this depend on pixel data you have not yet provided. General advice is power inject every 50 pixels for 5v pixels and every 100 pixels for 12v pixels. I personally inject every 25 pixels because I use buck converters than can only drive about 2A. IMO, putting the PSUs far away from the props they are driving runs up the cost because you need to use significantly thicker wire between the PSU and the pixels. My props have the PSUs mounted close to them. The wire used for the AC side of the PSU is only 16 awg and is easy to work with. On the output of the PSU I run 2 16AWG lines at 24v that then gets dropped to 5v by the buck converters.

The point here is that there are lots of ways to wire a show and I suspect that no two members on this forum do it the same way. You will need to pixk and choose what works for you.


Reply
Posts: 97
Topic starter
(@irrumater)
Estimable Member
Joined: 13 years ago

Thanks. With data only flowing one way I guess using 2 channels for the gutters would be the way to go. I have plans for power injection, based on countless you tube videos and reading every post on this site and others I can. I decided to go with more centralized power for the pixels on the house (gutters, windows, verticals) and power at the prop in the yard to start in order to have less parts in play on the first year. There is also a chance we might move in the spring so I didn't want to do too much custom work this year. Basically start adding/converting to pixels and figure out how it all works. We will see how it goes and I'm sure changes will be made for year 2.
Thanks as always for the advice.


Reply
Posts: 1420
(@1pet2-9)
Noble Member
Joined: 6 years ago

I like your plan, to try this first and then move to a new house later. On a 2+ story house, I actually like power injection better, because you can run wires out your windows and not even bother with weatherproofing your power supplies. What I learned, though, is to use supplies in the ~100w range, because they are fanless. The normal 350w supplies have fans,.and the noise can be annoying if they run all night in a living area.


Reply
Share: