Can I split a prop ...
 
Notifications
Clear all

Can I split a prop up between E682 controllers?

7 Posts
4 Users
0 Reactions
1,949 Views
Posts: 825
 DanJ
Topic starter
(@danj)
Prominent Member
Joined: 13 years ago
[#43700]

I am having significant issues getting signals out of xlights via unicast, so as a backup plan I am thinking through re-orienting my props on my controllers' outputs with all controllers in multicast (multicast working perfectly in xlights....). This re-orientation will force me to move four of my sixteen 3m strings of my megatree from one E682 to another to remain within the 7 universe multicast limit per controller. I didn't think it would matter how I break this up between E682s, but figured I would ask before jumping in head first!!! I was thinking the four strings that I move to the "second" E682 will need to be on another universe on the "second" E682. Is this correct? Thanks in advance!


6 Replies
Posts: 1168
(@keith-r)
Noble Member
Joined: 19 years ago
DanJ wrote:I am having significant issues getting signals out of xlights via unicast

What issues are you having?
All of my e682's are running in unicast.


Reply
JP90
Posts: 376
 JP90
(@jp90)
Reputable Member
Joined: 19 years ago
DanJ wrote:I am having significant issues getting signals out of xlights via unicast, so as a backup plan I am thinking through re-orienting my props on my controllers' outputs with all controllers in multicast (multicast working perfectly in xlights....). This re-orientation will force me to move four of my sixteen 3m strings of my megatree from one E682 to another to remain within the 7 universe multicast limit per controller. I didn't think it would matter how I break this up between E682s, but figured I would ask before jumping in head first!!! I was thinking the four strings that I move to the "second" E682 will need to be on another universe on the "second" E682. Is this correct? Thanks in advance!

Dan, Keith is right try to find out why it is not working if Keith 's is working with the same type of setup you are using as that may be the fastest way to go but to answer your question I use Vixen but the process should be the same all you need to do is look at the universe and channels you set up in the E682 ports you want to transfer those four strings to and remap the element strings in your software to those universes and channels. The E682 does not care what elements are connected to it as long as you match the elements in the software to the correct output on the E682.

Gary


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago
DanJ wrote:I was thinking the four strings that I move to the "second" E682 will need to be on another universe on the "second" E682. Is this correct? Thanks in advance!

No, they can be on the same universe as the first E682 if you want.

So let's say you use run-on addressing and your original 3-4 output ended on 7/270 and your original 4-1 started on 7/271.

It's fine if you instead plug those lights into e.g. 1-1 on another control and set that group to start on 7/271, even though it means Universe 7 will be picked up by both E682 controllers.

The network switch will just see this as 2 subscribers of the same multicast channel, which should work fine.


Reply
Posts: 825
 DanJ
Topic starter
(@danj)
Prominent Member
Joined: 13 years ago

Thanks so much for the replies everyone! As stated, I wanted to make sure I wouldn't goof it up by moving props from one controller to another.

Keith--are you using a PC or a PI to output to your controllers?

I have a LONG set of posts over at XL forum. Short version is that I am not able to send any XL test data or sequence data over my hardwired Ethernet switch to my controllers. I have tried a lot of stuff recommended over at that forum without success. I am going to take a very hard look at all my universes on the controllers; I have a feeling I goofed something up there that is precluding me from running in unicast. I have successfully run just some test lights (I am out of town right now...) on all four controllers when sending data out in multicast. I am using SACNView to monitor the info outputs; it has also shown no data sent in unicast and has shown data sent in multicast. I am running 1 F16 and 3 E682s via a 4 port Ethernet switch. I can see all controllers, can run their test signals, can change channels etc etc but not able to send XL data to them. I have been able to send SACNView and da_e131 data to them...


Reply
Page 1 / 2
Share: