JEC Pixels BOM
 
Notifications
Clear all

JEC Pixels BOM

18 Posts
5 Users
0 Reactions
5,317 Views
Posts: 864
Topic starter
(@deplanche)
Noble Member
Joined: 19 years ago
[#7563]

A while back I picked up a few the JEC DIY pixels (the green version, not the new white ones) and the power injector. Finally getting to the point where I think I know what I want to do with them, and am ready to assemble them. However, since there wasn't a coop for the parts for the boards, and there isn't a Mouser BOM list that I can seem to find, I don't have any parts to assemble them with. I did find parts list, but I really don't understand everything on there, and resistor sizes are based on the LEDs, so that is making me even more confused. So looking for someone to either make a mouser BOM for the pixels and the power injector, or explain to a non-techinical guy how to do so myself.

Thanks!


17 Replies
Posts: 386
 JEC
(@jec)
Reputable Member
Joined: 19 years ago

FYI - the only change between versions is the silkscreen color. All important components remain the same.

Unfortunately, I don't have a Mouser BOM to share. Most of my through-hole jellybean parts come from Jameco. Resistors are 100 / $1, etc. It's really easy to find if you have their printed catalog. Their online search section is unfortunately clunky.

I can look later tonight and find part numbers for some of the more obscure bits, such as the RJ45 jacks.

For the LEDs... Drive them at 20 mA per chain.

To calculate the resistance, use Ohm's law: V = IR, or I = V/R

V = 12V - (3 * Vdrop LED) - .7 (Vdrop Transistor).

Depending on the LEDs you purchased, green and blue may have a Vdrop of 3.4V. Most transistors drop .7v between collector and emitter.

V = 12v - (3 x 3.4) - .7
V = 1.1v

20 mA = 1.1v / R

.02 A = 1.1v / R

R = 1.1 / 0.2

R = 55 ohms

Make sense? Repeat with actual values from your LED datasheets for the five colors.


Reply
cbell
Posts: 462
(@cbell)
Honorable Member
Joined: 18 years ago

Here is the BOM that I used.

https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=4095b28d9f

I've built 8 pixels so far with this BOM with no problems. This does not include the 5 pin programming header because it was cheaper for me to buy 40 pin ones and cut them down.

Schematic is here

The 27K resistor is what I put at R112 for the channel set jumper. It and the 2 pin header aren't needed if you aren't going to use SRM's field programming firmware.

The 120, 270, & 330 resistors are what I used for my LEDs, you will have to use the formula JEC posted and the specs of your LEDs to determine what resistors you will need for locations R101-R110 (on the schematic).

I got the LEDs off of this guy on eBay wvengineer recommended him, and he worked with me to get me the quantities I needed and in a a timely manner for a great price.

If you have any more questions, please ask.

EDIT: I see by looking at JEC's calculations that I didn't take into account the voltage drop of the transistor, so my resistor calculations were a bit high for the LEDs I used, no biggie, but perhaps I could have gotten a little bit more brightness out of them had I included that in the calculation. Something to think about.

2nd EDIT:
The above BOM does not include a socket for the RS485 chips.


Reply
Posts: 864
Topic starter
(@deplanche)
Noble Member
Joined: 19 years ago

There are 6 of each color LED, so is the 3 x Vdrop because there are 2 sets of 3 LEDs (2 parallel sets of 3 LEDs in series)?


Reply
cbell
Posts: 462
(@cbell)
Honorable Member
Joined: 18 years ago
deplanche wrote:There are 6 of each color LED, so is the 3 x Vdrop because there are 2 sets of 3 LEDs (2 parallel sets of 3 LEDs in series)?

That's correct.


Reply
Page 1 / 4
Share: