Notifications
Clear all

Capacitor

10 Posts
6 Users
0 Reactions
4,808 Views
Posts: 5
Topic starter
(@chili)
Active Member
Joined: 19 years ago
[#1120]

Just call me dumb please. I am building a 10 channel light chasing or sequencing board. It calls for a 2.2uf electrolytic capacitor. There is a plus and minus on the diagram so I would assume it would take a polarized capacitor. How ever at radio shack (I do not have time to order) they had a 2.2uf capacitor (electrolytic but it is not pollarized. I do not think this will work. Straighten me out here. Thanks


9 Replies
Posts: 861
 xmus
(@xmus)
Noble Member
Joined: 19 years ago
chili wrote:Just call me dumb please. I am building a 10 channel light chasing or sequencing board. It calls for a 2.2uf electrolytic capacitor. There is a plus and minus on the diagram so I would assume it would take a polarized capacitor. How ever at radio shack (I do not have time to order) they had a 2.2uf capacitor (electrolytic but it is not pollarized. I do not think this will work. Straighten me out here. Thanks

what is the capacitor used for? decoupling? Where does it go? Can you share the design or a photo of the board? My guess is you'd be fine without a polarized cap, but i can't be sure...


Reply
NogginBoink
Posts: 482
(@nogginboink)
Honorable Member
Joined: 19 years ago

An "electrolytic" capacitor, by definition, is polarized.

I agree with xmus: just grab any ol' 2.2uF cap from the bench and solder it in there and you'll likely be fine.


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

There are non-polarized electrolytic caps. They are similar to putting two polarized caps in series, facing opposite directions. You can use a true non-polarized cap in a DC application, but you can’t use a homemade one in the same way.

Non-polarized caps are typically used in audio or AC motor applications.


Reply
wjohn
Posts: 1102
(@wjohn)
Noble Member
Joined: 19 years ago
chili wrote:Just call me dumb please. I am building a 10 channel light chasing or sequencing board. It calls for a 2.2uf electrolytic capacitor. There is a plus and minus on the diagram so I would assume it would take a polarized capacitor. How ever at radio shack (I do not have time to order) they had a 2.2uf capacitor (electrolytic but it is not pollarized. I do not think this will work. Straighten me out here. Thanks

Chili, I'll bet it is polarised. Just grab a 2.2uF cap, and just check the rated voltage is OK for the design (e.g. 16 V , 25V, 35V)

John.


Reply
Posts: 5
Topic starter
(@chili)
Active Member
Joined: 19 years ago

Well it is used for a 555 timing circuit. The package says it is50 volts max. Non-polarized for speaker crossover. 8kHzat 8 ohms, Axial leads.


Reply
wjohn
Posts: 1102
(@wjohn)
Noble Member
Joined: 19 years ago

do you have any other 2.2uF polarised caps you could use? That Cap is a non-polarised Cap, and while it may work, another polarised Cap would be better.


Reply
Posts: 5
Topic starter
(@chili)
Active Member
Joined: 19 years ago

No I do not but I am thinking of using another value cap. I have a 5.5 I think uf. I may try it


Reply
Posts: 210
(@sandy)
Estimable Member
Joined: 19 years ago

The 2.2 non-polar is still a 2.2 uf cap.
You can use it where ever 2.2uf is called for,
just be sure the voltage rating is higher than the working voltage.
The non-polar will be bigger that the polarized version,
just due to the need of making it non-polar,
The electrolytic's are polarized as it makes them smaller, and less expensive.


Reply
Posts: 5
Topic starter
(@chili)
Active Member
Joined: 19 years ago

Thanks everyone for your help. 😀


Reply
Share: