Board Coating
 
Notifications
Clear all

Board Coating

30 Posts
12 Users
0 Reactions
8,648 Views
Posts: 138
Topic starter
(@chris2879)
Reputable Member
Joined: 19 years ago
[#8721]

Does anyone coat their boards with some type of coating to protect them from the elements?


29 Replies
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Most do everything they can to prevent water from getting directly to the board. You can't prevent humidity very well... but if you're looking for an insulator, you can try Liquid Tape. It comes in a jar with an applicator brush, colors white or black (and maybe red) and you paint it on. Let it dry an hour or so and it's virtually waterproof. You'll find it in the electrical dept at Home Depot, Loew's, etc.

Some have used Plasti-Dip with varying results. Essentially the same stuff though.

Some use hot glue and that works very well, too. You just squirt it on where you need it, let it set and shazam. I do all my cat5 cables with that and it not only prevents water from getting into the rj45 from the cable side, it prevents the cord from wiggling in the connector, making it more solid.


Reply
Posts: 315
(@sky-lights)
Reputable Member
Joined: 17 years ago

Corrosion X - best water-repellent going . ( NOT water proof - but a repellent ) Spray , or brush it on , let it drip dry over night and your ready to go - just do NOT put in the RJ45 jacks area ... its a somma itch to get off .:shock:

All of those others mentioned are all good , except when it comes time ( if ever the time does come ) for replacement of parts - say you blow a triac .... or an opto ... now you have to "dig" it out . But with Corrosion X , its like an oily film on there ... so removal of parts is no different than like a board with nothing on it .
Myself and others use Corrosion X on our electronics ( servos and receivers )in our RC boats ( and other RC vehicles ). Its dielectric and you can , well , take a look at the videos I linked to it , for ya ;

read this article ( yep , Corrosion X has been used for water repelling for MANY years )
http://www.corrosionx.com.br/rcm.html


Reply
Posts: 95
(@fcky529)
Estimable Member
Joined: 19 years ago

heavy coat of spray laquer. I've used it on boards in specialty tools for my customers that worked outside. It hols up pretty well.


Reply
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago

What you are referring to is called a conformal coating. Its typically sprayed over a board to protect it from moisture.

http://en.wikipedia.org/wiki/Conformal_coating

Any good electronics supplier should carry the MG line of chemicals, here are their conformal coatings:

http://www.mgchemicals.com/products/protcoat.html

Also if you are concerned about immersion you could "pot" your boards. This is where you place the circuit board in a container and fill it with epoxy. While this may be way to much for what you are doing its still an option.


Reply
Posts: 393
(@rkhanso)
Reputable Member
Joined: 18 years ago

Is not just mounting in a broadbandstore enclosure good enough? I wasn't expecting to do any more protection from the elements.

Is it STRONGLY recommended to do this additional step? Maybe someone should start a poll...


Reply
NogginBoink
Posts: 482
(@nogginboink)
Honorable Member
Joined: 19 years ago

No need to coat 'em if you've got them in a good enclosure.

Heck, last year my 'enclosure' was a ziplog baggie and I had no issues.


Reply
omzig
Posts: 1603
(@omzig)
Noble Member
Joined: 19 years ago

I used CorrosionX on my boards, even with BroadbandStore enclosures. Last year one of my enclosures came open during a nasty ice storm. By the time I realized it the show schedule had started. The Ren24 was working perfectly despite a layer of wet ice on it. The next morning when it warmed up, the ice melted and left water droplets all over everything. For scientific purposes I fired the board up and it worked despite all of the water. I was sold.

It turns out that the enclosure came open because it was not mounted on a flat surface so it was slightly twisted when it was screwed down. This meant that the latch didn't quite line up correctly.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

I always use a small lock on the case just to keep curious fingers out of the boxes. Also prevents it from accidentally opening very far -- probably 1/4" or so at the most.

It's just enough of a deterrent that it seems to work.


Reply
Posts: 315
(@sky-lights)
Reputable Member
Joined: 17 years ago

Well to answer your question - is this other step required ? no ... but , for a little added protection - why not ?
The enclosures will STILL get dew - moisture inside , no matter what .
An ounce of protection is worth a pound of cure . 😎


Reply
Page 1 / 3
Share: