HELP!! Light o Rama...
 
Notifications
Clear all

HELP!! Light o Rama controller random flashing!!

13 Posts
3 Users
0 Reactions
4,868 Views
Posts: 374
Topic starter
(@mberta2)
Honorable Member
Joined: 13 years ago
[#43564]

Show is in 2 hrs. I run my show on xlights. It's a mix of pixels, rgb, and light o rama. The light o rama is running in dmx. I have 6 lor controllers. The 6th one has some lights just random flashing. And I cannot figure it out. Please help.

Sent from my SAMSUNG-SM-G935A using Tapatalk


12 Replies
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

What kind of lights, how far from the controller is the first light.


Reply
Posts: 374
Topic starter
(@mberta2)
Honorable Member
Joined: 13 years ago

Led lights. The same as all the other controllers. There is a 50ft cat5 between lor box 5 and 6. The lights for 6 are no more that 25ft away. Most of them being within a few feet

Sent from my SAMSUNG-SM-G935A using Tapatalk


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

So LED lights still leaves out a lot of information: RGB Pixels? DUMB RGB Nodes? Line Voltage (AC) strings? Low voltage DC strings? All of these are LEDs and all have different reasons for the symptoms you describe. Strip vs string, but you mentioned string so that answers that question.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
mberta2 wrote:Led lights. The same as all the other controllers. There is a 50ft cat5 between lor box 5 and 6. The lights for 6 are no more that 25ft away. Most of them being within a few feet

Sent from my SAMSUNG-SM-G935A using Tapatalk

If you swap boxes 5 and 6, does the issue move with the box?
If you replace the cable between 5 & 6 does the issue go away (this is the most common issue in a DMX setup).
If the lights are DC, is the DC voltage set within a half volt of the rated voltage?


Reply
Posts: 374
Topic starter
(@mberta2)
Honorable Member
Joined: 13 years ago

They are ac led lights

Sent from my SAMSUNG-SM-G935A using Tapatalk


Reply
Posts: 1049
(@phrog30)
Noble Member
Joined: 12 years ago

Also, create a new sequence and test just those lights to isolate any issues with your sequence.

Sent from my Pixel using Tapatalk


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
mberta2 wrote:They are ac led lights

Sent from my SAMSUNG-SM-G935A using Tapatalk

Ok This is a big thing. If the lights are AC then the issue has to be either the DMX controller or the communications cable to the controller. There is one additional item it could be. There are two implementations for the DMX passthrough circuits. Some controllers are passive (simply listen to the data going by) and others are active (regenerate the signal as it passes through the controller. Each of these types has a chance to introduce noise on the communications line that could cause the lights to flicker. The best first test is swapping the controllers to see if the issue moves with the controller or not.


Reply
Posts: 374
Topic starter
(@mberta2)
Honorable Member
Joined: 13 years ago

I ran the show with the flicker tonight. Nobody noticed (except me) and it was a huge success. I'm going to troubleshoot the problem tomorrow some more. The signal runs through quite a bit of cat5 before it gets to box #6. Could too long of cable cause some issues?

Sent from my SAMSUNG-SM-G935A using Tapatalk


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Yes it can but it would take an awful lot of CAT5 to have an issue. Unless of course you have coils in the cable or are running it past some big electrical noise sources. Both of those can cause issues. Most likely the cable itself has gone bad or the connectors have some corrosion on them.


Reply
Page 1 / 2
Share: