i think i got this but will post to get some feed back.
i am looking to do a 5v pixel tree. the tree will be 16 strings of 50 - 5v pixels. i plan on running tree on its own 4 string differential falcon receiver board. per my calculations, using 5v pixels, each string will be pulling 3 amps. so using a distro board will allow me 1 string per output, so i would need 2 of the distro boards. even if i went with 12v, i know that i could do more pixels per run before needing power injection, but at 2.5amps per 50 pixel leg, it would still be the same connections using the distro boards. at least that's what my calculations tell me. i was hoping to use powerinjection T's, but i would exceed the max amp per connection on the distro board.
if my drawing is correct, what cable guard enclosure would suffice to house a pwr supply, the diff board and 2 distro boards that will be placed at the base of the tree?
thanks for your input, and if i could please ask to keep the critique to the posted question. i am weighing all options as i know a 16 port board would nullify this post. however, at this time i do not have 1 and while the e682 would suffice nicely, my soldering skillz is still in the novice stage but i am learning and practicing.
Your making a tree much like mine, though I'm 50x12 5V off an diff receiver. I didn't use a fuse distro block, I instead soldered together two groups of six strands each and protected each side with a 15A fuse in line. It means I can't separate my strings, but I keep the tree together, and wrapped up in storage and I'm ok with the 'leg work' required to replace a bad pixel, should one every come up. The heat shrink solder sleeves make it easy enough to cut out and replace a strand in 10 minutes if I ever need too.
Notice I also mounted the box at the top of the tree, to keep wire lengths short. It's only about 12" of wire between the power supply and every leg of the tree.
This is a CG-1500
(link for picture: https://goo.gl/photos/i5ZCw93rMnU4ijWDA )
At 12v no injection needed. I ran my 800 node tree and 35 node star off the receiver board alone. Not one issue. I did run at 50% output. 100% is crazy bright
Sent from my iPhone using Tapatalk
lightsonmontague wrote:At 12v no injection needed. I ran my 800 node tree and 35 node star off the receiver board alone. Not one issue. I did run at 50% output. 100% is crazy brightSent from my iPhone using Tapatalk
You ran 800 pixels off 1 falcon receiver board?? What was the pixel count per output.
goverland wrote:Doing 5v 50x16 tree myself off one port F16v3. I plan on using one F8-Distro splitting the power to two 50 strings with tees. Each 50 string still gets power injection. Falcon F16v3 can do 1024 pixels per string. While most people run a single Falcon per mega tree, I want to try a single port.
is my math off? if the f8-distro is has 5amp fuses, are you planning on swapping the fuses? each 50 string of 5v pixels will pull 3 amps. so your tree, like mine, will be pulling 48amps.
rdj6107 wrote:is my math off? if the f8-distro is has 5amp fuses, are you planning on swapping the fuses? each 50 string of 5v pixels will pull 3 amps. so your tree, like mine, will be pulling 48amps.
He'll be OK with 5A fuses per 100 pixels. It take all white at 100% brightness for a long time to blow the fuse.
I run my 380 pixel grid sections behind a 7.5A fuse and I only blew a fuse once, when I left it full bright all white. Took about 3 minutes before it blew.
Sent from my Nexus 5X using Tapatalk
goverland wrote:Doing 5v 50x16 tree myself off one port F16v3. I plan on using one F8-Distro splitting the power to two 50 strings with tees. Each 50 string still gets power injection. Falcon F16v3 can do 1024 pixels per string. While most people run a single Falcon per mega tree, I want to try a single port.
This looks good to me. It's much like my tree which is 50x12 @ 5v. Ran it off two ports of a differential receiver off an F4V2. Each port has a 340 pixel limit in that configuration.
Sent from my Nexus 5X using Tapatalk
madsci1016 wrote:He'll be OK with 5A fuses per 100 pixels. It take all white at 100% brightness for a long time to blow the fuse.I run my 380 pixel grid sections behind a 7.5A fuse and I only blew a fuse once, when I left it full bright all white. Took about 3 minutes before it blew.
Sent from my Nexus 5X using Tapatalk
Had thought about changing the fuses, so this is good to know. Wouldn't be running 100% anyway. This will be my first year, so appreciate the advice.
Thanks,
Greg
rdj6107 wrote:You ran 800 pixels off 1 falcon receiver board?? What was the pixel count per output.
200 per port 235 on the last port. 12v pixels btw
Sent from my iPhone using Tapatalk

