mega tree base ring...
 
Notifications
Clear all

mega tree base ring material ideas....go!

28 Posts
12 Users
0 Reactions
28.8 K Views
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

Here is one of my sketches when I did my octagon. If you want rounder, then go to 16 sided and 16 spokes

pole

Reply
Posts: 205
(@barlav)
Estimable Member
Joined: 11 years ago

I used a piece of 1/2" EMT metallic conduit that I was able to bend by hand around some screws set in the circular pattern I needed. It has held up so far.

01

Reply
Posts: 844
(@ags0000)
Noble Member
Joined: 16 years ago

I may be misunderstanding the problem. Is the base ring on the ground or suspended? In any case, wouldn't a vertical tie directly down to (or into, if already on the ground) keep the ring from bending? I've used 1/2" EMT like this, suspended about 2' above the ground, and then tied it into the ground using cable and rebar stakes, 12 of them for a 14' diameter tree base. 3/4" EMT is quite a bit stronger - it was the top hoop of that same tree; it was 32" diameter, suspended from in six places, and carried the entire weight of a 500# structure.


Reply
Topic starter
(@jchuchla)
Illustrious Member
Joined: 15 years ago
ags0000 wrote:I may be misunderstanding the problem. Is the base ring on the ground or suspended? In any case, wouldn't a vertical tie directly down to (or into, if already on the ground) keep the ring from bending? I've used 1/2" EMT like this, suspended about 2' above the ground, and then tied it into the ground using cable and rebar stakes, 12 of them for a 14' diameter tree base. 3/4" EMT is quite a bit stronger - it was the top hoop of that same tree; it was 32" diameter, suspended from in six places, and carried the entire weight of a 500# structure.

The base ring is mostly suspended. The ground is on a slope. One point touches the ground, but the rest is hovering, as much as 24" or so. I tethered it to 6 or 8 stakes to hold it down. But it would bend quite significantly between the tether points. The way I look at it is that the tree exerts much more force on the ring than I could exert with a pipe bender. So if I can bend it by hand, it's not strong enough.

I can say that I'm actually surprised with the forces involved in the tree. Especially with wind and ice. I never expected this to be so involved.

So here's my new plan. I was looking around the house today for ideas, and I stumbled on an extra section of steel landscape edging I had laying next to the shed. This is basically steel flat stock with stake pockets punched into it. It's 3/16" thick, 4" wide, 16' long. https://www.siteone.com/p/332460 I can bend it horizontally into a big circle by hand, but because of the width of the stock, it won't bend in the other axis. I'll need a bit of modification to join these end to end to make the 40' circumference, but 4 bolts per joint should do that fine. I'll also bolt on pipe flanges to hold the spokes to keep it round and centered on the mast. The edging is 2.6 lbs/ft. So that should give it about 115 lbs of weight. I'll still stake it down with the chain and turnbuckles to the helical ground anchors. Now I just need to hope for a good weather day to do some fabrication before showtime.


Reply
Posts: 149
(@bob81354)
Estimable Member
Joined: 15 years ago

barav nice job can you tell us what the dimensions are of the circle is and are the vertical pipes going in to the ground then stake that to the ground ?


Reply
Page 3 / 6
Share: