Why would this happ...
 
Notifications
Clear all

Why would this happen ???????

21 Posts
6 Users
0 Reactions
8,994 Views
Goldie
Posts: 313
Topic starter
(@goldie)
Reputable Member
Joined: 19 years ago
[#9380]

l have 2 grinches connected to Ren c and Ren t. l am running led's and have rectified all and have resistors on all strings there are three colours Red Blue and White, when l run a chasing sequence for white say, l get red and blue flashing in time with the white chasing, red and blue is the same.
If l run a chasing sequence on my ren 64 there is no issue, before l ditch the Grinches is there anything l can do to solve this problem ?????????????


20 Replies
daviddth
Posts: 925
(@daviddth)
Prominent Member
Joined: 19 years ago

I have seen a few posts like this and it has me stumped. Last year I ran 2 lots of 2 Grinches (with 1 later upgraded to a ren64 and never had a problem, but I did have a few ZC issues. I have since upgraded the 1 remaining Grinch (and 2 595's) to use a 2cm square stripboard with the H11A11 opto used for ZC and the dimming, as well as channel "blips" that occasionally occurred no longer happen.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Is that a grinch by itself, or are you using a Ren-C with it?


Reply
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

Goldie,

not sure if its much of a help but i have one of my grinch/ren-c combo's still sitting around doing nothing. If it helps im sure i could drop it over tonight.

Also i could free up my ren64 combo as well if it would help

just give me a pm if you want it.

Edit: do you remember what code is in the ren-c's? did you end up with the new code to fix the 50hz flicker?


Reply
Posts: 138
(@d4rknessxkilla)
Estimable Member
Joined: 17 years ago

Are you running a Renard/ 595 converters with your Grinch? if you are theres one resistor that we cut and it fixed our problems with the LED's (it will still work with minis also..


Reply
Goldie
Posts: 313
Topic starter
(@goldie)
Reputable Member
Joined: 19 years ago
P. Short wrote:Is that a grinch by itself, or are you using a Ren-C with it?

Yes, l'm using a ren -c Grinch combo

scorpia wrote:Goldie,

not sure if its much of a help but i have one of my grinch/ren-c combo's still sitting around doing nothing. If it helps im sure i could drop it over tonight.

Thanks for the offer pete, l got hold of a grinch on Sunday, still same problem

Also i could free up my ren64 combo as well if it would help

if it ges to that stage l'll keep what l've got for this year and build some 64's for next year thanks again for the offer

just give me a pm if you want it.

Edit: do you remember what code is in the ren-c's? did you end up with the new code to fix the 50hz flicker?

, l'll get the pic's flashed tomorrow with the new software see how that goes

D4rknessxkilla wrote:Are you running a Renard/ 595 converters with your Grinch? if you are theres one resistor that we cut and it fixed our problems with the LED's (it will still work with minis also..

l'm not too sure what a renard/595 converter is, l have the renc Grinch combo.


Reply
Posts: 556
 jpb
(@jpb)
Honorable Member
Joined: 19 years ago

Earlier this year when I built my REC-C I had a problem with ghosting of channels using a Grinch. For example I would turn on Channel 12 and Channel 42 would start to flicker.

In the end I reflashed the chips to the latest firmware and cut a track on the REN-C and soldered a wire in. The hardware changes are documented in the asm file.

;; "This change requires a h/w change to the board - disconnect the ZC
;; signal from pin 2 of the HC02, and connect pin 2 of the HC02 to pins
;; 11,12 of the PIC.

The way I did it was easy to do and easy to reverse. See my post on the 29th of June in this thread. It even has photos
http://doityourselfchristmas.com/for...t=7044&page=10

Jon


Reply
Goldie
Posts: 313
Topic starter
(@goldie)
Reputable Member
Joined: 19 years ago

Hi Jon

The link does not work


Reply
daviddth
Posts: 925
(@daviddth)
Prominent Member
Joined: 19 years ago

Try this Goldie: http://www.doityourselfchristmas.com/forums/showthread.php?t=7044&page=10


Reply
Goldie
Posts: 313
Topic starter
(@goldie)
Reputable Member
Joined: 19 years ago

Thanks dave got pictures, if the reflashed picks don't work l'll give this a go


Reply
Page 1 / 3
Share: