multi ren-c
 
Notifications
Clear all

multi ren-c

22 Posts
7 Users
0 Reactions
15.4 K Views
Posts: 89
(@craftylag)
Estimable Member
Joined: 19 years ago

Computer to ren t about 8 feet. Rent t to renc about 6 inches. First Renc to first Grinch four inches. 6 inches to Second Ren c and four inches to Second Grinch. Ran this last year with older computer. Had trouble adding a third ren c and Third Grinch gave up last year just ran with two ren cs and two grinches. tried to run one dimming on serial and the other non-dimming on parallel. The first grinch on serial worked ok but the one on parallel didn't work at all. Outputs serial 1-64 com port 1 and second 65-128 on parallel port.


Reply
Posts: 556
 jpb
(@jpb)
Honorable Member
Joined: 19 years ago

If the REN-Cs are that close try running your ZC in parallel directly to each board.

In case you have not seen this, this is the wiki entry for the REN-C http://doityourselfchristmas.com/wiki/index.php?title=Renard-595_Converter
Depending on how you are delivering the ZC there are a couple of different build options.
Also, have you got the shunts in place on each grinch to feed the 5v back to the REN-C?

Jon


Reply
Posts: 89
(@craftylag)
Estimable Member
Joined: 19 years ago

Yes shunts are on grinches
I don't have ground in the power input. Would that have anything to do with it. Power light is on all boards. If I jumper zc to ren c's should I open it by removing a conponent. Could the ren t be bad. How do you check zc.
Thank you for taking time for me. I know who you are now. You display is one I used to help me to program mine in 2007 and 2008. Thanks for everything.


Reply
Posts: 556
 jpb
(@jpb)
Honorable Member
Joined: 19 years ago

I do not use a REN-T so I don't have any direct experience but I would try and work through the following sequence.

All the REN-C boards should be identical.

While keeping the Ren-C /Grinch combos in pairs, does each one work okay while connected directly to the REN-T? If so, this is good, all your boards should be okay. While you are doing this, check the value of R9 on each board, they should be 10K.

Test the cables you are using between the REN-Cs by using them in turn between the REN-T and a REN-C. If all the cables test okay move on.

It is possible that you have a dry joint on pins 7 & 8 of the RS Out RJ45 socket on one of the boards. Have a very close look at these and possibly reflow the solder while the boards are unplugged from everything and unpowered.

Connect two boards to your REN-T and check the ZC LED. If both are on try adding the third board.
If they are not both on, while they are hooked up and powered in their normal configuration, use a multimeter and carefully measure the DC voltage between R9 and Ground on the first REN-C. Then measure the voltage between the same points on the second board. Are the values similar?

If you are still having problems, keep the REN-C boards hooked up in their normal configuration but have no power connected and then measure the resistance from pin 7 on the RS In socket on the first REN-C to PIN 7 on the last REN-C. It should be zero resistance, if it isn't, work back through each of the connections to find where the bad connection is.

I hope this helps.

Jon


Reply
Posts: 89
(@craftylag)
Estimable Member
Joined: 19 years ago

Thank You at least I have a plan now I was lost with no directions to turn to. Wiki little confusing when it comes to Zc. If I don't find a high joint would the next step be to build individual Zc.[Will try parallel first].Thanks again. [Lights are up and running with three non-dimming grinches. Had to drop some slow songs].


Reply
Page 4 / 5
Share: