Ren128????
 
Notifications
Clear all

Ren128????

19 Posts
11 Users
0 Reactions
5,484 Views
Posts: 115
Topic starter
(@barnettd)
Estimable Member
Joined: 18 years ago
[#19334]

Would there be any reason that one could not add more PIC16F688 chips to the REN64 to make it a bigger REN controller??

I built a REN64 2 yrs ago, and I was wondering what would happen if I added more PIC chips to it to make it bigger. Meaning if I added 8 more chips to it making it a REN128.....

Can anyone give me any insight to any potential problems?? Voltage levels, communication standards.....etc...

Thanks

Dave


18 Replies
Aurbo99
Posts: 2804
Moderator
(@aurbo99)
Member
Joined: 19 years ago

I'm not an IEEE, but from my experiences with the Ren's I dont see why it could not work.

HOWEVER,

You adding a LOT of stresses doubling the RJ45's on a pcb if your doing a Ren64x2, and a TON of weight and stresses on the pcb if you looking at a SS style layout.


Reply
g2ktcf
Posts: 3651
(@g2ktcf)
Famed Member
Joined: 18 years ago

power for all the LEDs will require major changes in the power circuit to the board..you would be looking at a 2A system.

To me, its just as easy to have two boards side by side. You also gain some redundancy by having an extra controller that will replace a failed one. To do this with a 128 channel controller would be expensive.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

The oscillator circuit would have to change a bit as the current version can't drive that many PICs.


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago

I suggest superglue.


Reply
Posts: 2168
(@djulien)
Noble Member
Joined: 19 years ago
budude wrote:The oscillator circuit would have to change a bit as the current version can't drive that many PICs.

I've run 14 PIC16F688s from the same 18.432 MHz osc part successfully (1 motherboard + 2 daughter board Renards), although I might have been pushing the limits.

don


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

As I recall it supports ten loads but not 100% sure...


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago
budude wrote:The oscillator circuit would have to change a bit as the current version can't drive that many PICs.

Based on what? Low-level or high-level input currents? Capacitance? PCB trace length? I'm not sure I'd add too many CMOS loads without taking a look at the waveforms for reflections, ringing, etc, but I don't think that any restriction would show up in the datasheets.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Well I meant to say "may" need changing... I don't have the datasheet in front of me but there is some limit - thought it was around 10 loads of some type... In either case, for a standard light controller I would agree with Chris an just go with two Ren64's instead of coming up with something new.

There is the PropController that supports 128 channels now.


Reply
Posts: 115
Topic starter
(@barnettd)
Estimable Member
Joined: 18 years ago

I appreciate everyone's input with this query. I was just playing around with this idea for adding to my display controller inside my sign, instead of having the expense of building another Ren64.....

Thanks everyone..

Dave


Reply
Page 1 / 2
Share: