Ren 64 XC problems
 
Notifications
Clear all

Ren 64 XC problems

28 Posts
10 Users
0 Reactions
9,414 Views
Dave Burrows
Posts: 84
Topic starter
(@dave-burrows)
Estimable Member
Joined: 17 years ago
[#16161]

Hi all,

Last year i built 5 ren 64 xc's with no problems.
This year i have built 2 ren 64 xc's both with the same problem.
When i first hooked them up and and hit the test button on vixen, only the first light in each bank of eight, lights up on both boards.
I have ordered but not recieved my pic kit as yet so i don't have any diagnostic pics at this stage. But i have swapped pics from a working board and back again and they are o.k.
I have gone back over all soldered joints a second time.
I have checked the resistor banks and they have gone in with the dot to the square hole.
I'm thinking that i may have a wrong component in the wrong place or have been supplied with some wrong components.
(All components were purchased through x-on Aust with the mouser part numbers.)
I am working away at the moment and will not be back at home untill next Thursday, so i can't try any fixes straight up....sorry

Thanks in advanced

Dave

P9094296
P9094290
P9094294
P9094291

27 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

It might be your oscillator since it appears you've checked to make sure the PICs are programmed OK. Check the output with a DVM - it should be around 2.5v or so - just make sure it is not solid at 5v or 0v.


Reply
Greg in Canby
Posts: 854
(@greg-in-canby)
Prominent Member
Joined: 19 years ago

Check your resistor networks, not just the orientation. It sounds like a problem briefly experienced with a recent group buy. I'll search for the thread and edit this post when I find it.

http://doityourselfchristmas.com/forums/showthread.php?16331-Renard-64XC-LED-issue ...


Reply
boyelroy11
Posts: 757
(@boyelroy11)
Prominent Member
Joined: 17 years ago

Move along, nothing to see here....


Reply
g2ktcf
Posts: 3651
(@g2ktcf)
Famed Member
Joined: 18 years ago
boyelroy11 wrote:The resistor networks with issues were black in color. He appears to have the correct ones.

Bruce

Gents...he got these parts on his own.

Also, I have about 900 BLACK resistor networks that ARE correct. I have avoided using them to limit confusion as the orginals were black. Do not look at color! You need to check them with a meter!


Reply
Greg in Canby
Posts: 854
(@greg-in-canby)
Prominent Member
Joined: 19 years ago
g2ktcf wrote:Gents...he got these parts on his own.

Did not mean to imply any implications with the group buy Chris, just spit balling ideas. The link was only for researching possible solutions, as a lot of folks posted a lot of good ideas.

Greg


Reply
tom4writer
Posts: 85
(@tom4writer)
Estimable Member
Joined: 16 years ago

I want to test my resistor networks like Chris suggests. What is the best way to do that ?


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
tom4writer wrote:I want to test my resistor networks like Chris suggests. What is the best way to do that ?

The easier method may be to look up the part number on them and take a peek on Mouser to see which one you have.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

The dot on the case usually signifies the common lead, so you could check with a DVM between pin 1 and 2, 1 and 3, 1 and 4, etc. and come up with a resistance value. Note that if it's supposed to be 680, it may not be dead-on at that value but may be *close* to it. That's good enough.


Reply
Posts: 406
(@jboyles7)
Honorable Member
Joined: 17 years ago

Just plug in an SSR and test with the real lights to see if it is the LED or resistor network or something else.


Reply
Page 1 / 3
Share: