Firegod Flicker is ...
 
Notifications
Clear all

Firegod Flicker is back....

55 Posts
12 Users
0 Reactions
75.3 K Views
jcizek
Posts: 160
Topic starter
(@jcizek)
Estimable Member
Joined: 19 years ago
[#13111]

Firegod Flicker is back....RESOLVED!!!

For 2 weeks I have been testing and running sequences, checking channels, fixing lights, even ran the whole show through 2 full times wed night, not once did I ever see a flicker... tonight, now that I have "launched" my show to play every night, it looks like it's having a seizure... the flicker is HORRIBLE.

I have spent a bit of time tonight trying to isolate this... I am not 100% sure if all channels within a field module are flickering together, but one thing I do know is that the flicker is not the same across all field modules (and some have none at all).

The fact that this has not been seen once in 2 weeks makes me believe this is some kind of outside influence to the signal somewhere along the chain... If you look at the flicker close, it almost looks like a data burst from something. I have torn my hair out trying to go back through the house to see if something is on that wasn't before but can't find anything.

So, what I am really after here today is asking for any ideas on where to look for something that might be interferring with my controllers (btw- the Renard's are not having the issue at all) Don't know if David will see this post, but wondering what all you suggested to Greg in Canby (or maybe Greg will see this!!) to try on his setup this year?

Thanks... Between this problem and the ledtriks problems I am having this year, I'm about ready to go tear the entire display down and give this hobby up. This flicker is so bad you can't even see half of the sequencing because everything is flashing instead of just what should! (I didn't think it was possible to have TOO much flashy) 🙂

Thanks everyone. -James


54 Replies
Greg in Canby
Posts: 854
(@greg-in-canby)
Prominent Member
Joined: 19 years ago

James,

I hope you don't give up.

It's perplexing about the stable test but flickering show.

I believe (can't prove it) that using a 2 amp power supply and replacing the big CAP on the computer interface fixed my issue. I'm not however all set up nor fully tested with actual lights. I did my testing with either fake loads on the FM's or actual SSRs some with AC lights, some without. Appeared to be stable.

Other issues have pushed back my setup big time and to make things worse, I have to go to work tomorrow, gone til Monday.

Keep with it. My only advice is don't let small pieces of evidence limit your big picture troubleshooting.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

How long are the cables from the PC interface to the field modules? I don't own a Firegod system but I wonder if there may be a timing issue with the ZC if there is a long distance to travel or possibly if the cat5 cable goes near anything magnetic such as a motor or fluorescent light, which could inject noise into the cable. Would shielded cat5 (or perhaps cat6) be helpful?

I'm just throwing darts at the wall here, but I recall reading in a different thread that passing a ZC signal along too long of a cable to a Renard board causes inconsistencies, too.

I'll butt out of the conversation here because I know squat about Firegod... just trying to think outside the box a little at "outside influences."


Reply
jcizek
Posts: 160
Topic starter
(@jcizek)
Estimable Member
Joined: 19 years ago

Dirk, please don't butt out!! I appreciate the insight!! I have 7 field modules out there, 5 of them are within 20 feet of the PC modules, and 2 are about 50 feet away. 6 of the 7 modules within 20 feet are flashing, and only one single channel on one of the two 50 feet away is flashing. I really need to get a 2 channel scope setup on this so i can see where the problem is, one on the output of the FM and one on the input of the SSR.

Greg, I probably won't give up, I was just super frustrated (we've all been there right?) Just needed to walk away from it for a while 🙂
Do you know which capacitor it is that he suggested you replace? and how big of one to replace it with? That's an easy thing to try! Did you measure what kind of current draw you were seeing on the PC module? I wonder how close to the 1 amp it is...

I'll do some more testing today and get back with more details.

Thanks. -James


Reply
jcizek
Posts: 160
Topic starter
(@jcizek)
Estimable Member
Joined: 19 years ago

OK, I threw a scope on an opened up SSR to see what things look like.
When the lights are just sitting stable at 34% dimming, this is what they look like:

(sorry for the bad quality, my cell phone doesn't do macro very well)

Not really so much of a flicker to 100%, but sort of "hunts" around the right level.

Now, the input to the optocoupler of that SSR while sitting at 34% on the scope:

and a scope view of a dimming effort (I had the "test" channel panel up in vixen, set it to 0% and held the up arrow to let it slide to 100%)

Even though we don't see spikes in the dimming, the lights flicker to 100% quite badly during the dimming/brightening process.. Worse then by far than just sitting at one dimming level.

So the only thing I can see here is that this MIGHT be a zero crossing problem. Due to the fact that I see no vertical artifacts on the scope (ie, not falsely triggering) but there is horizontal movement indicating that the SSR is being sent the command at slightly different times.

I had the scope set to sync with "line". My biggest problem is that my scope is really old and in kind of sad shape (guess that's why i got it for free!) and I can't read the horizontal timing dial. I *think* it's set to 1ms/div in this video from the best i can read it 🙁

Anyone have any guesses with this info where I might go looking next?
Thanks. -James


Reply
Page 1 / 11
Share: