I saw a posting in the Olsen 595 forum about combining the Ren-C and DMX-Grinch into one converter.
I would love to see this go forward. The Ren-C Dimmable Grinch setup is the slickest system. Compared to the others The simplicity, parts count make this the #1 choice. The only thing that would make it better is the "addressable controller" idea that DMX provides. With the Renard protocol if you lose a controller in the middle of your daisy-chain everything is out of wack. Adding DMX to the dimmable Grinch sorts all that out.
The bit about the DMX dongle being expensive...If someone could write a plug-in that was pointed directly at a serial port then any $5 usb-serial dongle would work with any of the myriad 232-485 converters out there.
tfmacz wrote:The bit about the DMX dongle being expensive...If someone could write a plug-in that was pointed directly at a serial port then any $5 usb-serial dongle would work with any of the myriad 232-485 converters out there.
There's a few wrinkles re: using a serial port to generate DMX directly.
First, it's hard to make the serial port generate a 'break' signal - it doesn't match up with any standard bit or baud timings.
Serial ports like to be fed bytes of data to be transmitted at a specific speed. It's not so easy to generate signals of arbitrary timing.
Second, it may be tricky to find a serial port that runs fast enough. You need 250,000 bits per second (that's 4 microseconds per bit) and a very narrow tolerance for timing error.
At full speed, a DMX transmitter can update 512 8-bit channels about 44 times per second.
That's why most of the computer ==> DMX interfaces out there include a USB interface and a small microcontroller. The processor receives data from the computer and then assembles the DMX packets for broadcast.
The interface will happily do it's job over and over and over, without worrying about the computer's operating system getting in the way or other programs taking momentary precedence.
After design, setup and tooling fees, the parts in one of these interfaces can be had for about $10.
Consider, though, that computer controlled lighting is a very narrow market.
No reasonable company would consider selling these for only $10 - $15 profit unless orders were for thousands or even millions of units.
However... Hardware hackers, who often place no value on their free time, are a different story. 🙂
JEC is correct in all cases. The other thing to not is the Open doesn't use a micro to generate DMX. It uses a USB to serial adapter. In theory you could use any USB to serial adapter assuming it appeared as a com port in device manager and it wasn't locked to the "standard" baud rates.
I recently purchased a parallax USB to serial adapter for my propeller. It "looks like" the Open device to vixen when plugged in. If I add a 75176 to it I would end up with another open dmx dongle.
I would bet that if you purchased a cheap USB to serial adapter, cracked the case, and soldered up a 75176 it would work. That might be an interesting project.
DynamoBen wrote:I would bet that if you purchased a cheap USB to serial adapter, cracked the case, and soldered up a 75176 it would work. That might be an interesting project.
I tried that, TheParallax USB uses the FTDI bridge chip. The usb-serial dongles I have use different bridge chips. Can't remember the make. The Vixen DMX plug-in is looking specifically for the FDTI chip:
"Error opening FTD2XX device 0"
But because the OpenDMX is just a USB to RS485 I was hoping that there might be more support for some of the other USB-Serial bridge chips out there...
JEC wrote:
However... Hardware hackers, who often place no value on their free time, are a different story. 🙂
hmmm....no shortage of those around here, i think.
I have a parallax "Propeller Plug" which looks to be an FTDI chipset also. Now that you mention it I guess the plugin does depend on the FTDI chipset driver. 🙁
Don't forget that this is also an option. http://www.dlpdesign.com/usb/usb232.shtml
That is what I used for my Open DMX device. Literally I soldered on some resistors and a 75176 and I was ready to go.
Ok I am not into all this fancy programming talk etc. I can get by with programing Renard chips but for now that is as far as I have learned.
So can you make a Dimmable DMX board for the olse/grinch or not? Is yes, I would be glad to beta one!
Ben
The one part I was able to make a DMX open dongle out of the dlp designs usb adapter
http://www.mouser.com/search/ProductDetail.aspx?R=626-DLP-MM232R
One thing about this adapter is it does appear to have quite a few "capabilities" other than just a usb adapter. (eeprom configurable)
It can xmit RS485 directly from the adapter, it also has multiple clock rates.
So you have this working? If so I will add it to the wiki.
BTW based on a request in another thread I'm building a DMX dongle. I have a proof of concept working on my bench. It will be a multi universe USB DMX dongle when complete.
http://www.doityourselfchristmas.com/forum/viewtopic.php?t=357
Is your adapter like the Pro only cheaper?
Bill
