Finally Affortable ...
 
Notifications
Clear all

Finally Affortable Snowfall Tubes (FAST)

448 Posts
68 Users
0 Reactions
263.1 K Views
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
chilloutdocdoc wrote:They're charlie-plexed, only one of them is ever on at a time, I recall him in chat saying he was running them at less than 20mA each.

You can have more than one on at a time with charlie-plexing - at least 7 that I can see...?


Reply
chelmuth
Posts: 1077
Topic starter
(@chelmuth)
Noble Member
Joined: 16 years ago

You are correct I could have 7 on at one time. However the firmware is written that only one is ever on at one time.. Plus as Josh stated I didn't have 51Ohm resistors so I originally used 100Ohm which left the LED's running at 9.5ma.. and still plenty bright enough..

wwwgator - If you look at the firmware it tells you what pins are that I used and the order that they fire.. So below the first LED to fire would be Pin3 to Pin13.. If you follow the colored diagram it's exactly how i wired it.. and once you kind of look at how it's done it's really kind of easy.

;1 = RA4 (Pin3)
;2 = RA0 (Pin13)
;3 = RA1 (Pin12)
;4 = RA2 (Pin11)
;5 = RC0 (Pin10)
;6 = RC1 (Pin9)
;7 = RC2 (Pin8)
;8 = RC3 (Pin7)
;
;1-2 Done;1-3 Done;1-4 Done;1-5 Done;1-6 Done;1-7 Done;1-8 Done
;2-3 Done;2-4 Done;2-5 Done;2-6 Done;2-7 Done;2-8 Done
;3-4 Done;3-5 Done;3-6 Done;3-7 Done;3-8 Done
;4-5 Done;4-6 Done;4-7 Done;4-8 Done
;5-6 Done;5-7 Done;5-8 Done
;6-7 Done;6-8 Done
;7-8 Done


Reply
tweist
Posts: 394
(@tweist)
Reputable Member
Joined: 18 years ago

Great job. I am impressed. I'm thinking, maybe next year I will make some. This year budget is already spent, and then some.
Really nice job.
Oh and thanks for the video. That really shows how well it works.


Reply
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago
chelmuth wrote:IIdeally I'd like to get it to a point where there are a few configurable options in the firmware such as setting a flag for maybe a "dimming tail" or other ideas. I'd like some input on the software and if possible some help with the code. I'm 1 week into learning assembly, so I know I've got a ways to go.

Corey:

And I absolutely stink at ASM, so I can't be of much help to you there.

I've just spent some time at YT and V looking at videos of snowfall tubes and what I find different about yours is that you're lighting only one pair of LEDs at a time, while most of the others light a larger swath of LEDs.

Also, other tubes seem to ramp-up to full on and then ramp down to off the swaths as they descend; is this the "dimming tail" you mentioned above?

Lastly, yours seem to be rather slow compared to others that are out there.

I think I'd want to build these as only 12- or 14-inches long ... would there be a provision to have a shorter length?

Thanks so much for taking the time and energy to work on this.

\dmc


Reply
chelmuth
Posts: 1077
Topic starter
(@chelmuth)
Noble Member
Joined: 16 years ago

Just a change in the delay routing could make it faster.. currently i have it set to decay so that it falls slower as it gets lower. I had a discussion yesterday that someone thought it should go faster.. I could probably put a setting in there that if you put a 1 in before compiling it would speed up or a 0 would make it slow.. those are kind of the configurable options i was looking for having.. If you wanted shorter yeah you could make it shorter length.... just use less pins and remove the un-used pins from the code..also this was my first attempt and I could probably make it about 5" shorter just by having the LED's closer together also.. It's completely possible. I had just planned on around 24" as I was going to cut the tubes mentioned earlier in half (4') or quarters (8').. Yes the dimming tail was what i was refering to as far as the ramp-up you mention. That would require a re-write of the code that I'm not quite up to that skill level yet. It needs to have some sort of software PWM implemented and I have yet to find a good example that I've been able to hack apart and put into that and I'm not completely comfortable with the interrupt routines which would be required. Which is why i was hoping someone with a little more coding experience could help with. I was just laying the ground work and idea for innexpensive tubes. Currently they should be less than 10$ per tube.. yes they require some work but that's the fun part.


Reply
Page 6 / 90
Share: