Notifications
Clear all

FGII

30 Posts
12 Users
0 Reactions
15 K Views
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago
[#2219]

Fgii

I have finished with the new FGII design.

The design includes:
*An RJ-45 connection for connection to the current FGDimmer PC interface
*A connection for a 9 pin serial cable
*A connection to relay the serial data to other FG field modules
*A wireless serial modem
*On board 120VAC to 5vdc power supply
*On board 5 vdc to 3.3 vdc power supply for the wireless modem
*On board zero cross signal
*Each of the 32 outputs is individually dual fused with 3.6mm x 10mm fuse holders (incandescent mini light string fuses)
*The 120VAC power is rectified and instead of Triac SSRs using multiple parts, I am using IGBTs with PWM programming in the PIC (a much lower cost solution)
*Diodes on each IBGT to protect the controller circuit

I have run a few PSPICE models and I am currently ready for the prototyping phase.

I have attached the PCB Artist files (schematic and PCB design) from http://www.4pcb.com/ . The PCB Artist software allows the schematic to be changed and the changes be forwarded to the PCB design so if the schematic is correct, the PCB will be correct with respect to the net connections. Most all of the parts have part numbers so if you right click on a part in either file you can take a look at the part number. I have not completed the part number documentation yet but it is next on the list.

The serial modem can receive the data and the module can then retransmit the data to the other four modules so you only need one serial modem for four field modules.

If anyone out there can review the files and see if I have done something wrong. I have no doubt this will draw some comments from the forum.

Thanks for any constructive comments you can offer.

edit: attachments removed, new ones can be found below


29 Replies
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Since I can't view those files on this computer (and haven't even installed the s/w on my Windows computer), how much does the schematic here differ from the one in the other FGII thread?

--

Phil


Reply
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago
P. Short wrote:how much does the schematic here differ from the one in the other FGII thread?

*Changed the connections between the MAX232 and the SN65176 I/Cs
*Added grounds to the RS485 connections
*Added the connectors to the 32 load outputs
*Added a fuse to the load side so they are fused on + and -
*Added diodes to the PIC outputs for some low cost isolation protection
*Added the 2200uF cap to the input of the 5VDC regulator because I am planning on having a little noise on the power side in my new project

See attached.

edit: attachments removed, new ones can be found below


Reply
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago

It should be noted that this design will accomodate AC or DC. With DC, the transformer and bridge rectifier is bypassed via jumpering.

The IGBTs are rated for 13 amps each at a cost of $1.13 each.


Reply
A Marchini
Posts: 426
(@a-marchini)
Reputable Member
Joined: 19 years ago
FireGod wrote:It should be noted that this design will accomodate AC or DC. With DC, the transformer and bridge rectifier is bypassed via jumpering.

The IGBTs are rated for 13 amps each at a cost of $1.13 each.

This seems like a fun design, can the PIC generate PWM on all those channels at once?

Have you used the XBees much? Were you considering using the Zigbee protocol or some other kind of mesh net?

Tony M.


Reply
Page 1 / 6
Share: