Page 22 of 42 FirstFirst ... 12202122232432 ... LastLast
Results 211 to 220 of 414

Thread: Rbl ?

  1. #211
    Join Date
    Nov 2018
    Location
    Houston, Texas
    Posts
    1,389
    Post Thanks / Like

    Default Re: Rbl ?

    Quote Originally Posted by angus40 View Post
    Do a very simple safe test with 1 single pixel(3 leds) brand new - not used.
    no unclipped ends !
    Thanks walking away for a bit helped not sure what caused second pop to die but this one is working not sure if a lot brighter but colors seem much more vibrant ...I have 5 strips in it .
    Thanks again angus




    Sent from my iPhone using Tapatalk

  2. #212
    Join Date
    Nov 2018
    Location
    Houston, Texas
    Posts
    1,389
    Post Thanks / Like

    Default Re: Rbl ?

    5 bullets in each of these for comparison





    Sent from my iPhone using Tapatalk

  3. #213
    Join Date
    Dec 2011
    Posts
    6,370
    Post Thanks / Like

    Default Re: Rbl ?

    I can see them from my house Well done .

  4. #214
    Join Date
    Nov 2018
    Location
    Houston, Texas
    Posts
    1,389
    Post Thanks / Like

    Default Re: Rbl ?

    Have it on full power white to check for heat problems will try for 1 hour first as I never have mine on longer than 10 min anyway as they are always blinking and flashing or off .


    Sent from my iPhone using Tapatalk

  5. #215
    Join Date
    May 2007
    Location
    New Jersey
    Posts
    1,341
    Post Thanks / Like

    Default Re: Rbl ?

    Very nice! What do you like better, the bullets or the 3 pixel flat nodes? Unfortunately all my flat nodes are TLS3001...

    Jeff
    Please consider becoming a Supporting Member of DIYC. Show your thanks to those who make this place possible.

  6. #216
    Join Date
    Nov 2018
    Location
    Houston, Texas
    Posts
    1,389
    Post Thanks / Like

    Default Re: Rbl ?

    Quote Originally Posted by Jeff Millard View Post
    Very nice! What do you like better, the bullets or the 3 pixel flat nodes? Unfortunately all my flat nodes are TLS3001...

    Jeff
    Personally I like the 3 nodes better but cost goes up a few bucks vs bullets but have to say the color is more vibrant and itís brighter so eventually I may Change all 11 of mine over to these at some point .


    Sent from my iPhone using Tapatalk

  7. #217
    Join Date
    Nov 2018
    Location
    Houston, Texas
    Posts
    1,389
    Post Thanks / Like

    Default Re: Rbl ?

    Update on heat - I ran full white for 2 hours or more at 100 % and had no issues there was some heat on the back side of the stem but I will make the stem with vents so itís not solid to allow for some dissipation and air flow .


    Sent from my iPhone using Tapatalk

  8. #218
    Join Date
    Nov 2018
    Location
    Houston, Texas
    Posts
    1,389
    Post Thanks / Like

    Default Re: Rbl ?



    The new screw on adapter for the strip lights with vents


    Sent from my iPhone using Tapatalk

  9. #219
    Join Date
    Aug 2008
    Location
    Delaware, OH
    Posts
    4,382
    Post Thanks / Like

    Default Re: Rbl ?

    In the long run you will be glad you did that.
    Everything looks brighter when looked at standalone.
    Once these are in a group with other lights you will be glad their glow is as good as possible.
    Super Nice work !
    Quote Originally Posted by wilmar View Post
    Personally I like the 3 nodes better but cost goes up a few bucks vs bullets but have to say the color is more vibrant and itís brighter so eventually I may Change all 11 of mine over to these at some point .


    Sent from my iPhone using Tapatalk

  10. #220
    Join Date
    Dec 2017
    Location
    Indiana
    Posts
    85
    Post Thanks / Like

    Default Re: Rbl ?

    I have been following this thread since it started. Are you printing these on a CR10 or an Ender 3 Pro? I know the CR10 has a HUGE bed print area not sure about the Ender 3 pro. However, I have a Prusa MK3s and was wanting to print these as these turned out great (Good Job by the way). I was thinking I could line them down my driveway standing up right like on a yard stake or something. However, I didn't know if I would have to scale it down to be able to print it. Then if I scale it down then everything you made wouldn't fit correctly. Like 6 of the 3 rectangular lights would no longer work because everything would be smaller. My print bed max is 8.3" (x) x 8.3" (y) x 9.8" (z). So I wasn't sure what your build size of these was.

Page 22 of 42 FirstFirst ... 12202122232432 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •