Page 1 of 2 12 LastLast
Results 1 to 10 of 16

Thread: Renard Plus TR-24 PIC programming problems

  1. #1
    Join Date
    Sep 2007
    Location
    Valley Center, Ks
    Posts
    295
    Post Thanks / Like

    Default Renard Plus TR-24 PIC programming problems

    I have never programmed a PIC18F4520 before. I keep getting “Target device was not found (could not detect target voltage VDD). You must connect target device to PICkit 3”. I have used this setup before with PIC16F1825 chips. I changed the jumpers per the board. See pics below. Any ideas?








    Sent from my iPhone using Tapatalk
    Dave
    128 Olsen 595 Vixen controlled channels
    about 30,000 lights

  2. #2
    Join Date
    Dec 2013
    Location
    Winter Haven Florida
    Posts
    2,839
    Post Thanks / Like

    Default Re: Renard Plus TR-24 PIC programming problems

    you could program the chip right in the board
    Last edited by TazChaLet; 10-31-2018 at 09:04 PM.
    James WinterHaven Fl

  3. Likes Ruppro liked this post
  4. #3
    Join Date
    Dec 2013
    Location
    Winter Haven Florida
    Posts
    2,839
    Post Thanks / Like

    Default Re: Renard Plus TR-24 PIC programming problems

    J2 J3 J4 J5 J6 J7 is that set on 1/2 or 2/3 should all be 2/3
    James WinterHaven Fl

  5. Likes Ruppro liked this post
  6. #4
    Join Date
    Sep 2007
    Location
    Valley Center, Ks
    Posts
    295
    Post Thanks / Like

    Default Re: Renard Plus TR-24 PIC programming problems

    Not sure. The adapter isn’t labeled. They were all the other direction for the PiC16F1825. So I moved them for this since it said 2-3


    Sent from my iPhone using Tapatalk
    Dave
    128 Olsen 595 Vixen controlled channels
    about 30,000 lights

  7. #5
    Join Date
    Dec 2013
    Location
    Winter Haven Florida
    Posts
    2,839
    Post Thanks / Like

    Default Re: Renard Plus TR-24 PIC programming problems

    I am not sure since this has no listing for that chip that is why I suggest putting it back in board and doing it that way
    James WinterHaven Fl

  8. #6
    Join Date
    Dec 2013
    Location
    Winter Haven Florida
    Posts
    2,839
    Post Thanks / Like

    Default Re: Renard Plus TR-24 PIC programming problems

    click to enlarge image

    Screenshot_1.jpg
    James WinterHaven Fl

  9. #7
    Join Date
    Sep 2007
    Location
    Valley Center, Ks
    Posts
    295
    Post Thanks / Like

    Default Re: Renard Plus TR-24 PIC programming problems

    So I just connect the PICkit 3 onto the program header. Where did you get that picture? From the assembly doc?


    Sent from my iPhone using Tapatalk
    Dave
    128 Olsen 595 Vixen controlled channels
    about 30,000 lights

  10. #8
    Join Date
    Dec 2013
    Location
    Winter Haven Florida
    Posts
    2,839
    Post Thanks / Like

    Default Re: Renard Plus TR-24 PIC programming problems

    yeah it is off the renard plus site
    James WinterHaven Fl

  11. #9
    Join Date
    Aug 2013
    Location
    Greer, SC
    Posts
    73
    Post Thanks / Like

    Default Re: Renard Plus TR-24 PIC programming problems

    I have flash all 12 of my tr24 on the board itself.

    DO NOT PLUGIN THE BOARD TO POWER

    THE BOARD IS POWERED THRU THE CABLE, and should not be powered through the board
    [2017] 32 Renard Channels, 3360 LED Lights
    [2018] 240 Renard Channels, 14070 LED Lights, 2 projectors, and one donkey

  12. #10
    Join Date
    Sep 2007
    Location
    Valley Center, Ks
    Posts
    295
    Post Thanks / Like

    Default Re: Renard Plus TR-24 PIC programming problems

    Tried on the board this morning before work. No dice. Same error message.






    Sent from my iPhone using Tapatalk
    Dave
    128 Olsen 595 Vixen controlled channels
    about 30,000 lights

Page 1 of 2 12 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •