Page 4 of 4 FirstFirst ... 234
Results 31 to 38 of 38

Thread: SSRez in the news - again!!!

  1. #31
    Join Date
    Feb 2009
    Location
    Plymouth, MN
    Posts
    9,049
    Post Thanks / Like

    Default Re: SSRez in the news - again!!!

    The DIGWDF engineers thought a little video of the prototype might be helpful to folks that are still curious whether this thing actually works... Here you go.

    https://vimeo.com/248263419

    Last edited by dirknerkle; 12-21-2017 at 01:31 AM.

    http://digwdf.com/store/
    The DIGWDF Store will be closing at the end of December -- but there's still a little stock left!
    While it's still open, please check us out for blinky-flashy gizmos that nobody else on the planet makes!

  2. #32
    Join Date
    Dec 2007
    Posts
    163
    Post Thanks / Like

    Default Re: SSRez in the news - again!!!

    I'm finally getting around to assembling these. I'm a little confused with step 14 though. Are we strapping across the back of the board, or are we just connecting the power through the holes on each side of the board? Do you have a picture or wiring diagram of just that area? Thanks.

  3. #33
    Join Date
    Feb 2009
    Location
    Plymouth, MN
    Posts
    9,049
    Post Thanks / Like

    Default Re: SSRez in the news - again!!!

    Solder the wires into the holes so they stick upward, and then you can slide the buck down over them and solder the buck to the wires.

    It may be easier for some to solder wires to the buck's terminals, bend them down so they fit through the PCB holes, solder at the PCB bottom and clip the excess off.

    buck_converter2.png
    Last edited by dirknerkle; 05-21-2018 at 05:25 PM.

    http://digwdf.com/store/
    The DIGWDF Store will be closing at the end of December -- but there's still a little stock left!
    While it's still open, please check us out for blinky-flashy gizmos that nobody else on the planet makes!

  4. #34
    Join Date
    Dec 2007
    Posts
    163
    Post Thanks / Like

    Default Re: SSRez in the news - again!!!

    Wish I would have bought more of these. If anyone bought some of these and isn't going to use them, I would be willing to buy. Thanks.

  5. #35
    Join Date
    Dec 2007
    Posts
    163
    Post Thanks / Like

    Default Re: SSRez in the news - again!!!

    Will these work with the SSROZ also?

  6. #36
    Join Date
    Feb 2009
    Location
    Plymouth, MN
    Posts
    9,049
    Post Thanks / Like

    Default Re: SSRez in the news - again!!!

    Quote Originally Posted by slug View Post
    Will these work with the SSROZ also?
    Electrically, yes. But I think the SSROZ's tall fuse might preclude everything from fitting inside a TA200 case....

    http://digwdf.com/store/
    The DIGWDF Store will be closing at the end of December -- but there's still a little stock left!
    While it's still open, please check us out for blinky-flashy gizmos that nobody else on the planet makes!

  7. #37
    Join Date
    Dec 2007
    Posts
    163
    Post Thanks / Like

    Default Re: SSRez in the news - again!!!

    Great. I can remedy the fuse. Thanks.

  8. #38
    Join Date
    Feb 2009
    Location
    Plymouth, MN
    Posts
    9,049
    Post Thanks / Like

    Default Re: SSRez in the news - again!!!

    If you plan to put the adapter on top of the SSROZ, you should put a layer of insulation between the two so the two don't touch. A layer of cardboard or even coroplast should be all that's needed. The adapter was designed to be electrically inert on one end so that it actually rested on top of the SSREZ's TRIACs, but the same may not work for the different parts locations of the SSROZ.

    http://digwdf.com/store/
    The DIGWDF Store will be closing at the end of December -- but there's still a little stock left!
    While it's still open, please check us out for blinky-flashy gizmos that nobody else on the planet makes!

Page 4 of 4 FirstFirst ... 234

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •