Page 51 of 51 FirstFirst ... 41495051
Results 501 to 508 of 508

Thread: Espixel by Bill Porter

  1. #501
    Join Date
    Jan 2015
    Location
    Folsom, CA, USA
    Posts
    1,630
    Post Thanks / Like

    Default Re: Espixel by Bill Porter

    Quote Originally Posted by ukewarrior View Post
    I also have the Pops-O-Matic programmer to do this job.
    Boards are $1 and you buy your own components.
    wiki: http://www.doityourselfchristmas.com...ESP_Programmer
    I got and built your Pops-O-Matic today. Good little board.

    I did a little modification I'd like to share. Maybe on your next run you can include.
    Your board is setup for a on-off-on SPDT switch. I installed that switch, then added a jumper from the 100R switch point to a TTL point, marking it 5V. With the switch in one position it powers from the terminal board, and in the other, it powers from the 5V terminal of the TTL. The TTL powering is my preferred.

    Pop-o-matic.jpg
    In Lights Therapy

  2. #502
    Join Date
    Nov 2015
    Posts
    3
    Post Thanks / Like

    Default Re: Espixel by Bill Porter

    Quote Originally Posted by beeiilll View Post
    I have been putting an Arrow BOM together and have all on it except for the 2x4 pin socket. Seems like Arrow does not stock or carry that.

    It comes up with $3.05 for one BOM from Arrow! Here is the BOM:

    Quantity Part Number Description
    1 LD1117V33 IC REG LDO 3.3V 0.8A TO220AB
    1 LM78L05ACZ IC REG LDO 5V 0.1A TO92-3
    1 ECA-0JM221 CAP ALUM 200UF 20% 8V RADIAL
    1 C320C104M5R5TA CAP CER 0.1UF 50V X7R RADIAL
    1 ZVN3306A MOSFET N-CH 60V 270MA TO92-3
    2 RN55D3300FB14 RES 330 OHM 1/8W 1% CF AXIAL
    1 SE008014711 Conn Unshrouded Header HDR 6 POS 2.54mm Solder ST Thru-Hole
    1 1N4148 DIODE GEN PURP 100V 200MA DO35
    1 FSM4JH SWITCH TACTILE SPST-NO 0.05A 24V
    1
    5-534206-4 Conn Socket Strip SKT 8 POS 2.54mm Solder ST Thru-Hole
    1 20020327-D051B01LF TERM BLOCK 5POS 3.81MM PCB HORIZ


    If anyone comes up with the 2x4 socket from them please post the item number.

    Bill

    7/22/2017 - Added in the BL208 8x2 connector onto the list. You will have to cut it down to make a 4x2 out of it but that is not a big deal. Thanks to davros for finding this one on the Arrow site.
    I've been working on getting the parts together to build some ESPixelSticks tiny that I ordered form ukewarrior

    Currently the part number 5-534206-4 works on Arrow for the Conn Socket Strip SKT 8 POS 2.54mm Solder ST Thru-Hole Tube. (https://www.arrow.com/en/products/5-...e-connectivity)

    but the Tinys (per the Wiki) :
    The ESPixel Pops Tiny board has the same BOM but you omit:
    - D1 - One diode. This must be: 1N4148
    - One tactile switch. 6mm x 6mm.
    - One six pin header. Readily available 2.54mm (.1") pitch.
    Last edited by Casper; 11-13-2018 at 05:56 PM.

  3. #503
    Join Date
    Dec 2012
    Location
    Silsbee, Tx
    Posts
    1,067
    Post Thanks / Like

    Default Re: Espixel by Bill Porter

    I bought a pack of 20 from China on Ebay
    but here is a USA seller on Ebay,

    https://www.ebay.com/itm/20PCS-2x4-P....c100012.m1985

  4. Likes Casper liked this post
  5. #504
    Join Date
    Jan 2015
    Location
    Folsom, CA, USA
    Posts
    1,630
    Post Thanks / Like

    Default Re: Espixel by Bill Porter

    Maybe here....$5 min order, ships USA via USPS about 10 days delivered.

    https://www.taydaelectronics.com/2x4...in-header.html
    In Lights Therapy

  6. Likes Casper liked this post
  7. #505
    Join Date
    Aug 2018
    Posts
    6
    Post Thanks / Like

    Default Re: Espixel by Bill Porter

    I have them in stock at Addicore

    https://www.addicore.com/2x4-Female-Header-p/ad261.htm

    We use them for a breadboard ESP breakout adapter we designed.

    Andre

  8. #506
    Join Date
    Aug 2008
    Location
    Columbus, OH
    Posts
    4,107
    Post Thanks / Like

    Default Re: Espixel by Bill Porter

    So.... I have personally ordered from addicore when I have needed a USA based supplier all the way back to the first pixel pops group buys.
    I have also directed at least 20 different folks their way when specifically asked for a supplier that I know doesn't sell PUYA based ESP-01's.
    (I don't know Andre or anything like that.)
    But, I have not had anyone tell me that his supply of ESP's hasn't worked.

    Yes, you pay more than aliexpress, ebay or amazon.
    But, as many have found out, its a crap shoot when you shop from these sources for a lower price.

    I would not buy any of these modules from anyone unless they can tell me EXACTLY what memory chip is on their boards with a PICTURE to confirm that fact !

    Quote Originally Posted by andreaddicore View Post
    I have them in stock at Addicore

    https://www.addicore.com/2x4-Female-Header-p/ad261.htm

    We use them for a breadboard ESP breakout adapter we designed.

    Andre

  9. Thanks andreaddicore thanked for this post
  10. #507
    Join Date
    Aug 2018
    Posts
    6
    Post Thanks / Like

    Default Re: Espixel by Bill Porter

    Thanks for the kind words ukewarrior!

    Andre

  11. #508
    Join Date
    Dec 2012
    Location
    Silsbee, Tx
    Posts
    1,067
    Post Thanks / Like

    Default Re: Espixel by Bill Porter

    A message from Addicore says my order was shipped today.

Page 51 of 51 FirstFirst ... 41495051

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •