Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: Renard SS24 Troubleshooting

  1. #11
    Join Date
    May 2007
    Location
    Mooresville, NC
    Posts
    7,245
    Post Thanks / Like

    Default Re: Renard SS24 Troubleshooting

    Power chip??
    James Family Christmas - 1600 channels of SS Renard channels
    Website - http://jamesfamilychristmas.com/
    Facebook - James Family Christmas


  2. #12
    Join Date
    Dec 2011
    Location
    Gaithersburg, MD
    Posts
    153
    Post Thanks / Like

    Default Re: Renard SS24 Troubleshooting

    re-ran the diagnostics.
    Pulled out all the chips. tested and same results.
    This time, I swapped out the U2, U4 and U5 from another unit and w/ the Diag PIC in the U6 position, I get a very brief flicker on lightbulb connected to two (no LEDs on) when I connect the power.

    the voltage regulator was replaced.
    2016 Migrating to Vixen 3.2
    Vixen 2.5x
    120 Channels
    2015 5 RenardSS24 @ 20,600 lights
    2014 5 RenardSS24 @ 18,600 lights
    2013 3 RenardSS24 @ 9,900 lights
    2012 2 RenardSS24 @ 6,000 lights
    2011 began researching
    www.KentlandsChristmas.com

  3. #13
    Join Date
    May 2007
    Location
    Mooresville, NC
    Posts
    7,245
    Post Thanks / Like

    Default Re: Renard SS24 Troubleshooting

    If you want to send the controller to me I can look it over. Just PM me and I will get you the address.
    James Family Christmas - 1600 channels of SS Renard channels
    Website - http://jamesfamilychristmas.com/
    Facebook - James Family Christmas


  4. #14
    Join Date
    Dec 2011
    Location
    Gaithersburg, MD
    Posts
    153
    Post Thanks / Like

    Default Re: Renard SS24 Troubleshooting

    Will do


    Sent from my iPhone using Tapatalk
    2016 Migrating to Vixen 3.2
    Vixen 2.5x
    120 Channels
    2015 5 RenardSS24 @ 20,600 lights
    2014 5 RenardSS24 @ 18,600 lights
    2013 3 RenardSS24 @ 9,900 lights
    2012 2 RenardSS24 @ 6,000 lights
    2011 began researching
    www.KentlandsChristmas.com

  5. #15
    Join Date
    Feb 2008
    Location
    Warminster, PA
    Posts
    1,655
    Post Thanks / Like

    Default Re: Renard SS24 Troubleshooting

    Did you try reflowing the oscillator? I forget whether the diag firmware uses it but if it does and it's not connecting that would do it.
    Chris
    [URL="http://www.maloneylights.com"]http://www.maloneylights.com[/URL]
    [URL="http://halloween.maloneylights.com"]http://halloween.maloneylights.com[/URL]
    [URL="http://ctm.maloneylights.com"]http://ctm.maloneylights.com[/URL]

  6. #16
    Join Date
    Dec 2011
    Location
    Gaithersburg, MD
    Posts
    153
    Post Thanks / Like

    Default Re: Renard SS24 Troubleshooting

    No I did not only the U6.


    Sent from my iPhone using Tapatalk
    2016 Migrating to Vixen 3.2
    Vixen 2.5x
    120 Channels
    2015 5 RenardSS24 @ 20,600 lights
    2014 5 RenardSS24 @ 18,600 lights
    2013 3 RenardSS24 @ 9,900 lights
    2012 2 RenardSS24 @ 6,000 lights
    2011 began researching
    www.KentlandsChristmas.com

Page 2 of 2 FirstFirst 12

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •